What have you done to your mk4 (golf/bora) today?

[blackers10]

I don't see why you would as there is no adjustment available in the strut top/bottom and sway bar?
if its driving sweet, I wouldn't bother ??

[Sirocco20348]

fun times ahead for you Mr Sirocco!
My golf just got a set of Joms coilovers, MUCH better now since replacing 213k km old shocks.
very happy with them.
now to alter my driveway curbing to make it not scrape the front on the way in etc. (my driveway is a killer not just because its ultra low)
[ATTACH=CONFIG]12999[/ATTACH]

New suspension is such a great feeling. I like the height you have your car at. Whats your next move it's a never ending saga haha

[blackers10]

Next I would like to get a 3" DP and I have a pod filter setup in the works I am piecing together.
then I can get a stage 2 Custom Code tune

The height is practical especially for my driveway haha.. even still I need to rig up some sort of ramp situation to help with the front end clearance

[caputo9]

Haven't posted in here for a while so i thought id give you guys a bit of an update
Heres how my beast currently sits with coils, 25mm rear spacers and 5mm front spacers (want 15mm bolt ons if anyone can help). Feel free to check my build
Enjoy

[JustCruisn]

I removed the foam and taped up the ac blend door last night.
Was a fiddly job but no more vent foam flying around my car.

[blackers10]

I have to do my blend door or something motors or cogs.. It goes clunk clunk brrrr brrrr brrr constantly while driving if the climatronic is on or off

[SLAJ]

Haven't posted in here for a while so i thought id give you guys a bit of an update
Heres how my beast currently sits with coils, 25mm rear spacers and 5mm front spacers (want 15mm bolt ons if anyone can help). Feel free to check my build
Enjoy

Looking awesome man

[JustCruisn]

Windscreen wipers have been going dead slow lately. Pulled them and attempted to fix. driver side was seized. Broke a mounting tab trying to free it up. Quick trip to the wrecker got it sorted.
The donor car had a revised version, plastic covers to stop water getting into the shaft.

[MCiN7]

Pulled out 1 of 2 failed thermo fans.
F#ck MK4's are ***.

If I can remember correctly you needed to take off the most of the front?

[ryana89]

On a VR or TDI you might, it's easy enough on the GTI.
Just expensive, a nuisance and disappointing that VW can screw up such fundamental/simple things.

[JustCruisn]

You can get the fans out easily enough on the GTI. just had to remove the plastic air intake bits and push the rad hose to the side.

I pulled the big fan out and managed to pull it apart and fix.
I found the brushes were not getting close enough to the commutator.
A bit of silicon grease and they slipped into the correct position. Working perfectly now.

[Duke999R]

Today I finally got around to fitting my R32 H&R front sway bar and poly front control arm bushes. Bushes were easy, but that sway bar was a bastard of a job. Dropped the subframe, took out the old one (it was rubbing on the drive shaft).

Got the new one in... kinda. It wasn't fitting right, and I couldn't figure out why. It was jammed up against the front of the steering rack, and I couldn't get the sway bar bushes to line up. Took it back out and my brother says "It's bent." So it was. Bought it used off a forum user and it had obviously been involved in a bingle at some point. Won't name any names, but I'm sure he must have known it was bent. Straightened it out with a bit of work on the press and back in it went.

Had a hell of a time getting the steering rack reattached to the subframe, as the R32 sway bar was a couple of mil bigger in diameter and the locating tab on the steering rack fouled it. Out with the grinder, touched up the tab and tickled it back in.

Then had hella trouble getting the sway bar bush brackets located into the slot, got that in with a bit more tickling with the hammer.

Gotta thank my little bro ASA572 who got out of his sick bed to come and help. 41 degree heat didn't help much , but it's all good now. Sway bar clears the driveshaft (R32 item runs underneath) and the poly control arm bushes feel good.

[caputo9]

Looking awesome man

Thanks man

[JustCruisn]

Another trip on the car ambulance


Cam sensor gone again

[RolfGolf]

At the risk of whoring this out again, how good does it look?! Loving the silver and black - very crisp - glad you got the clunking issue sorted too. (Must be a relief to find out it's not the dreaded gearbox!)

Today I finally got around to fitting my R32 H&R front sway bar and poly front control arm bushes. Bushes were easy, but that sway bar was a bastard of a job. Dropped the subframe, took out the old one (it was rubbing on the drive shaft).

Car looks good in the signature pic - need more pics though.

Cam sensor gone again

Is that a common fault?