VCDS (VAG-COM) codes and programmable options for Golf Mk7

[scaper28]

Hi Don

Sorry I was trying to say the menus to enable RC are missing out of my channel map , hopefully you will see what I mean from the link


I have attached a link to my channel map.

https://www.dropbox.com/s/h2q1hyr23xo6diu/adpmap-09-5Q0-937-084-N.CSV?dl=0

Regards

Craig

[DV52]

Hi Don

Sorry I was trying to say the menus to enable RC are missing out of my channel map , hopefully you will see what I mean from the link

I have attached a link to my channel map.

https://www.dropbox.com/s/h2q1hyr23xo6diu/adpmap-09-5Q0-937-084-N.CSV?dl=0

Regards
Craig

Craig: What a very interesting problem - thank you for raising it!!!

Fortunately your car and mine have the same BCM - see as follows:
scaper28 - BCM

SW:5Q0-937-084-N   HW:5Q0-937-084-N ---  Cent. Elect. --- SA: 03147,,,,
;Component:BCM MQBAB M   H14 0106, Coding:03000842C241027B0FA44080B1040328100A000000000000000000000000,,,
;EV_BCMCONTI,10001,EV_BCMBOSCH_010.rod,,
;Thursday,29,June,2017,08:31:39:20275
;VCDS Version: Beta 17.6.0 (x64)  Data version: 20170602 DS274

DV52 - BCM

SW:5Q0-937-084-N   HW:5Q0-937-084-N ---  Cent. Elect. --- SA: 31347
;Component:BCM MQBAB M   H14 0106, Coding:03001842C24102FB0FA4400000040308100A000000000000000000000000
;EV_BCMCONTI,010001,EV_BCMBOSCH_010.rod
;Friday,30,June,2017,18:20:07:16808
;VCDS Version: Beta 17.6.0 (x64)  Data version: 20170602 DS274

I was able to replicate your problem by creating an Admap of my BCM using the same Beta software version as in your file (i.e. Beta SW ver 17.6.0). I then compared the ver 17.6.0 admap with an admap from a previous Ross Tech version (i.e. ver 16.8.0)

I was pleasantly surprised to discover that the latest Beta version software found 78 x new adaptation channels in my BCM that were previously unknown.

However, I also sadly discovered that the latest Beta verion software lost 68 x old adaptation channels from my BCM that were previously known

Here is the list of the Adaptation channels that were lost from my previous version SW (I've highlighted your missing channels):

ENG122976-ENG128460-Remote_Start_Adaption-Rueckmeldung_bei_Aktivierung
ENG122976-ENG128461-Remote_Start_Adaption-Kombi_Fahrerhinweis_m_Uebernahme_RSt
ENG126561-ENG100480-Innenbeleuchtung KL 58xs min-Y2
ENG126561-ENG100773-Innenbeleuchtung KL 58xs min-Y3
ENG126561-ENG101574-Innenbeleuchtung KL 58xs min-X1
ENG126561-ENG102140-Innenbeleuchtung KL 58xs min-X3
ENG126561-ENG115658-Innenbeleuchtung KL 58xs min-x0
ENG126561-ENG115659-Innenbeleuchtung KL 58xs min-y0
ENG126561-ENG99557-Innenbeleuchtung KL 58xs min-X2
ENG126561-ENG99777-Innenbeleuchtung KL 58xs min-Y1
IDE01268-ENG02321-Windshield wiper-Tippendes_Frontwaschen
IDE01268-ENG02322-Windshield wiper-Frontwischer_Abtauposition
IDE01268-ENG126844-Windshield wiper-Washer_Tipwiping_Variant
IDE02269-ENG02272-Acknowledgement signals-Quittierton bei zweitem ZV-AUF-Befehl
IDE02269-ENG02273-Acknowledgement signals-Quittierton bei zweitem ZV-ZU-Befehl
IDE02711-ENG02323-Rear Window Wiper-Einzelansteuerung Heckintervallwischen Zeitintervall 1
IDE02711-ENG02324-Rear Window Wiper-Einzelansteuerung Heckintervallwischen Zeitintervall 2
IDE02711-ENG02325-Rear Window Wiper-Einzelansteuerung Heckintervallwischen
IDE04923-ENG02307-Turn signal control-Abbruch Komfortblinken
IDE04924-ENG126816-Driving light and parking light-Standlicht aus
IDE04927-ENG126845-Window heater-FSH Automatik
IDE04927-ENG126846-Window heater-Abschalttemperatur fuer Heckscheibenheizung
IDE04927-ENG126847-Window heater-Abschalttemperatur fuer Frontscheibenheizung
IDE04928-ENG126842-Anti-theft device-Ueberwachung Innenentriegelungshebel
IDE05142-ENG02314-Access control-Heckfreigabe_Ohne_Verzoegerung
IDE05142-ENG02315-Access control-Deaktivierung_Laderaumschliessung_extern
IDE05142-ENG02316-Access control-LS_Taster_Togglefunktion
IDE05142-ENG02317-Access control-Nutzfahrzeug_Schliessung
IDE05142-ENG02318-Access control-Wiederverriegelung_Laderaum
IDE05142-ENG06090-Access control-Mindestbetaetigung_HDF_Innentaster
IDE05142-ENG115722-Access control-Elektrische Laderaumabdeckung
IDE05142-ENG125652-Access control-Servoheck Schlossansteuerung
IDE05142-ENG125653-Access control-Deaktivierung_SAFE_ueber_DWA_Deaktivierungstaster
IDE05142-ENG126837-Access control-Entsafen mit autorisierte Klemme 15 Ein
IDE05142-ENG126838-Access control-Softtouch-Betaetigung senden
IDE05142-ENG126839-Access control-Entriegelungwunsch_verzoegert_waehrend_Zuziehvorgang
IDE05142-ENG126840-Access control-Vorrastenhaenger_Freigabe
IDE07470-ENG02308-After-run for park light-Bedingungen zur Standlichtbegrenzung
IDE07470-ENG02309-After-run for park light-Bedingungen zur Parklichtbegrenzung
IDE07470-ENG02310-After-run for park light-Faktor fuer Verfgbarkeitstimer
IDE07470-ENG02311-After-run for park light-Standlicht-Verfgbarkeit
IDE08542-ENG02339-Access control 2-Spiegelanklappen_bei_Wiederverriegelung
IDE08542-ENG115869-Access control 2-Virtuelles_Pedal
IDE08542-ENG125654-Access control 2-Nachsaven_nach_Verdecklauf
[COLOR=#0000ff][B]IDE08542-ENG125655-Access control 2-Regenschliessen_ein_aus
IDE08542-ENG125656-Access control 2-Regenschliessen_art[/B][/COLOR]
IDE08542-ENG125657-Access control 2-Remote_Unlock_Lock
IDE08542-ENG126610-Access control 2-Signalisierung_Spiegelanklappung
IDE08542-ENG126611-Access control 2-virtuelles_pedal_HMI_einstellbar
IDE08542-ENG126841-Access control 2-Profilfunktion fuer Anklappung der Aussenspiegel
IDE08542-ENG128459-Access control 2-easycloselight_aktiv
IDE08786-ENG126628-Assistance light functions-LS_Error_Ausgabe
IDE08786-ENG126817-Assistance light functions-Umfeldleuchte als Manoevrierleuchte
IDE08786-ENG126818-Assistance light functions-Fahrlichtwarnung_Hinweis_Konfig
IDE08786-ENG130581-Assistance light functions-Fahrlicht_Hinweis_mehrfach
IDE08788-ENG126629-Dyn. turn signal modes-Telematikblinken1_STS_Blinken Telematikblinken2_OCU_Blinken
IDE08788-ENG126819-Dyn. turn signal modes-Emergency_alert_blinken
IDE10298-Alternating park position 1
IDE10299-Alternating park position 2
MAS01490-ENG02328-Energy management-Praediktives_Energiemanagement
MAS01490-ENG116830-Energy management-Energy_Management_Adaptation
MAS05934-ENG02319-Convert. top oper.-Remote Lock Unlock Timer s1
MAS05934-ENG02320-Convert. top oper.-Remote Lock Unlock Timer s3
MAS05934-ENG126630-Convert. top oper.-Reichweitenbegrenzung fuer Servoheck schliessen
MAS05934-ENG126843-Convert. top oper.-ZV verriegeln bei Klemme 15 Ein[TABLE]
[TR]
[/TR]
[/TABLE]

Just to be clear - the list above are those adaptation channels that appeared in the BCM admap using version 16.8.0 BUT do not appear in the BCM admap using Beta version 17.6.0

Alas, I have no idea why this has happened - I suggest that you contact Ross Tech for a response. However, if you want to proceed with the tweak - please use a previous release VCDS version

Don

[scaper28]

Don

Thank you so much I will do that now , I thought I was going mad not being able to find it .

Much appreciated for your help and time .

well giving that I can find 16.8.0 download , as typically every time I update I delete the old downloads so I am now searching google for a previous version download of it .

Craig

[ala]

Is it possible to activate a indicator in the cluster for the low beam light or the drl light?
Just to know when the low beam is on or off, or the drl is on or off.

[stark27]

Question: Anyone have an OBDeleven? Is it worth the money?

https://www.autoinstruct.com.au/product/obdeleven-audi-volkswagen-skoda-diagnostic-system/

[SloAu]

Question: Anyone have an OBDeleven? Is it worth the money?

OBDeleven – Audi & Volkswagen Diagnostic System – Shop – AutoInstruct

Yea it is worth it's money, tested on numerous golfs and polos plus a few skodas really handy

[DV52]

Is it possible to activate a indicator in the cluster for the low beam light or the drl light?
Just to know when the low beam is on or off, or the drl is on or off.

ala: Hi. You didn't mention what flavor mk7 that you own (which build year and which model).

There are a couple of adaptation channels in the BCM that appear to be appropriate for your wants. They are:

• IDE06864-ENG115733-Daytime running lights-Tagfahrlichtkontrollleuchte (for earlier model BCM) which has a factory setting of not active. "Tagfahrlichtkontrollleuchte" translates to "DRL indicator light" - I think. Later model BCMs use ENG10575-ENG115733-Außenlicht_Front-Tagfahrlichtkontrollleuchte

• IDE04924-ENG115858-Driving light and parking light-Kontrollleuchte fuer Begrenzungslicht (for an earlier model BCM) which has a factory setting of not active. " Kontrollleuchte fuer Begrenzungslicht" translates to "Indicator light for marker light" - I think. Not quite the same as the low beam, but the marker light should be illuminated whenever the low beam is switched-on. Later model BCMs use ENG10584-ENG115858-Außenlicht_uebergreifend-Kontrollleuchte fuer Begrenzungslicht.

But don't get too excited because whilst these 2 x channels look hopeful, when I've tried to activate these in the past - nothing happened! My totally unfounded belief is that notwithstanding that these two channels are indeed correct to initiate the indicator lights on the dashboard, the Instrument panel (in my car) doesn't have these required indicator lamps fitted (this is just a guess). But my car has a black and white bog-standard instrument panel.

So, if you want to experiment on your mk7 (perhaps, your car has a higher-end instrument panel) - try changing the settings and see what happens! If you get the same results as I did - just revert the settings back to their original values - nothing lost!!

Good luck

Don

[ala]

Ohh. 2015 variant 1,4 tsi 122hp. comfortline.
Is it also possible to turn off the light in the cluster wenn the drl is on, so it turns on together with the low beam, because then the indicator in the cluster is not necessary.
I've turned on the rear lights together with the front drl.
But am using the foglights as drl.

I'll try the other thing next week.

[UserName123]

Can anyone help with my Golf Gti facelift 2017 settings? I have the outer DRL and blinkers working, but not the inner ones. I see that there are bulbs inside the inner stripes but they for some reason are not illuminated.

I would like to make it work so that both DRL stripes are illuminated and also the inner blinker would blink.

Anyone knows how to do it already for the facelift?

[DV52]

Can anyone help with my Golf Gti facelift 2017 settings? I have the outer DRL and blinkers working, but not the inner ones. I see that there are bulbs inside the inner stripes but they for some reason are not illuminated.

I would like to make it work so that both DRL stripes are illuminated and also the inner blinker would blink.

Anyone knows how to do it already for the facelift?

UserName123: Hi - I note that your location is "Hell"! Are you a devotee of Dante's 14th-century epic poem "Divine Comedy", and is there a sign over the gates there saying "Abandon hope all ye that enter here"?

Anyhow: to your question - I'm not sure but if you post-up an adaptation channel map of the module @ address hex09 (which VCDS calls the "BCM"), then I'll have a look at what's possible in the new Golf

Don

[UserName123]

UserName123: Hi - I note that your location is "Hell"! Are you a devotee of Dante's 14th-century epic poem "Divine Comedy", and is there a sign over the gates there saying "Abandon hope all ye that enter here"?

Anyhow: to your question - I'm not sure but if you post-up an adaptation channel map of the module @ address hex09 (which VCDS calls the "BCM"), then I'll have a look at what's possible in the new Golf

Don

Not quite hell, but the city I'm from does start with the first three letters so quite close.

And allright I can post it, first I'll have to see how to do it.

[DV52]

Not quite hell, but the city I'm from does start with the first three letters so quite close.

And allright I can post it, first I'll have to see how to do it.

Arrh I see - Helsinki!!

Thanks for the admap. It's the first that I have seen for the new-look Golf and you are correct - there has been much that has changed in the BCM.

I will need to have a look at the connection pin-out for the new BCM to make sense the channel settings, but it appears at first glance that the only headlight Leuchte-sets that are used are the low-beams. Clearly the new LED based headlight fittings have been integrated into the Convenience CAN bus in a different way to the older models - intriguing. The leuchte-sets for the taillight fittings appear to be more traditional, but there are still some significant changes!

Incidentally, this BCM is one of the new version that doesn't have any code-string. Instead, all the software switches that were in Byte/Bits, are now embedded into adaptation channel settings - making the channel count in this BCM a whopping 2,040-ish!

So- my apology, but I don't believe (at this time) that it's just a matter of energizing additional Leuchte-sets to get the two inner LED bars to operate as you want. But as I said, my understanding of this new arrangement is not good - perhaps another forum member here can be more helpful

Don

[UserName123]

Here is a link to the map: Dropbox - adpmap-09.CSV

[UserName123]

DV52, do you need some additional information perhaps ?

[DV52]

DV52, do you need some additional information perhaps ?

Username: hmmm....... I have to admit that I can't find anything remotely appropriate in your BCM admap. The traditional 4 x DRL Leuchte sets are:

Leuchte2SL VLB10

Leuchte3SL VRB21

Leuchte4TFL LB4

Leuchte5 TFL RB32

I was hopeful that I would find a pair of these Leuchte-sets that simply needed to be energized to address your problem. But alas, all 4 x Leutche-sets are not activated in your BCM - which as I said previously suggests that these LEDs in front headlight fittings on your car are controlled by another method (interesting!).

How would you feel about sharing the auto-scan report on your car? You can remove the VIN from the report before posting it here if you want (for anonymity)? That way we can see what other equipment is fitted to the vehicle - which hopefully might reveal an alternative path of inquiry.

I also need to get hold of a wiring diagram for the vehicle - this is often a valuable resource when dealing with these problems. But this takes longer time.

Don

PS: if/when you post-up the auto-scan, remember to use the "code" tags: before you paste the data , add [code] and at the end add [ /code] without the space between "[" and "/" . Here's an example of how it should look:

Tuesday,25,March,2014,11:55:50:03521
VCDS -- Windows Based VAG/VAS Emulator
VCDS Version: 14.2.1.2
Data version: 20140212


VIN:[COLOR=#0000ff][B] ********  [/B][/COLOR] License Plate: 
Mileage: 6411 kms   Repair Order: Beta Ver 14.2.0



--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Chassis Type: AU (5Q0)
Scan: 01 02 03 08 09 10 15 16 17 19 42 44 52 5F

VIN:[COLOR=#0000ff][B] ***********[/B][/COLOR]

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
5F-Information Electr. -- Status: OK 0000
 
-------------------------------------------------------------------------------
Address 01: Engine (J623-CHPA)       Labels: 04E-907-309-V1.clb
   Part No SW: 04E 906 016 G    HW: 04E 907 309 A
   Component: 1.4l R4 TSI   H08 5272  
   Revision: WAH08---    
   Coding: 01250032242405082000
   Shop #: WSC 00028 028 00079
   ASAM Dataset: EV_ECM14TFS01104E906016G 002006
   ROD: EV_ECM14TFS01104E906016G.rod
   VCID: 26431A2059EACC04DD-8073

No fault code found.
Readiness: 0110 0001

-------------------------------------------------------------------------------
Address 02: Auto Trans (J743)       Labels: 0CW-927-769.clb
   Part No SW: 0CW 300 045     HW: 0AM 927 769 G
   Component: GSG DQ200-MQB H43 4510  
   Revision: 00043014    Serial number: CU501212296246
   Coding: 0014
   Shop #: WSC 00028 028 00025
   ASAM Dataset: EV_TCMDQ200021 001001
   ROD: EV_TCMDQ200021_AU37.rod
   VCID: F6E38A6049CA7C842D-80A3

No fault code found.

If you click "Reply with Quote" tab on the lower RHS of this post, you will see how the "code" tags operate