VCDS (VAG-COM) codes and programmable options for Golf Mk7

[gaucho]

My Vehicle status only shows up first when there is a message such as door open or fuel needed, otherwise what comes up first is what I last left it on.


Sent from my iPhone using Tapatalk

that's exactly how I would like it to do, but here it always come to the Status screen. Is it possible to fix?

[agentthumb]

that's exactly how I would like it to do, but here it always come to the Status screen. Is it possible to fix?

Try this:

Before you power on the car, close all your car doors first. It should just go to the last page.

Door open, low fuel, service reminder or any other warning will hijack your screen.

I agree tho, it's nice that it tells me my door is open, but it should return to the original screen once I have closed my door, and there are no other statuses to show...


Sent from my iPhone using Tapatalk

[LunchboxVRS]

I leave mine on oil temp but If you make a call, put in a address to Nav to it will change to that until you switch it back. It's just what it does.

[gaucho]

Try this:

Before you power on the car, close all your car doors first. It should just go to the last page.

Door open, low fuel, service reminder or any other warning will hijack your screen.

I agree tho, it's nice that it tells me my door is open, but it should return to the original screen once I have closed my door, and there are no other statuses to show...


Sent from my iPhone using Tapatalk

Here even with no warnings it goes back to Status, is there any vcds config to change that? Doors open I can see in the driver's panel, no need to see it in the central panel screen.

[agentthumb]

Here even with no warnings it goes back to Status, is there any vcds config to change that? Doors open I can see in the driver's panel, no need to see it in the central panel screen.

I don't believe so. Others might know tho.


Sent from my iPhone using Tapatalk

[fabbromix]

Hi Raga can be activated with VCDS DAB radio function, or there is to change hardware clicked down?

[fabbromix]

Fabbromix: Ciao e Benvenuto nel forum

ho Limitato la mia risposta alla Tua Domanda SPECIFICHE circa il Famoso filo 9 dal manico alla centralina BCM. Ecco lo schema elettrico Lo Lo Lo Lo Lo Lo Lo Uno Che ho sviluppato Qualche tempo fa, il Che mostra provengono i 9 fili Sono collegati Tra Euro-Interruttore (Quello che si chiama "la maniglia") e il BCM.



Se la Vostra auto non e Stato Montato in fabbrica, con la luce del Sensore (pioggia / umidita), poi il filo mancante sarebbe probabilmente Essere Quello che gestisce la Funzione AUTO. Venite Si Può VEDERE Dalle mie foto, Questo e il Collegamento con PIN 2 # sull'Euro-Interruttore e l'altra estremita del Cavo è collegato al pin # 16 su Socket C sul BCM.

E 'facile trovare il PIN # 2 sull'Euro-Interruttore, Perché i numeri Codice Codice Codice Codice Codice Codice Codice Codice dei pin di Base Sono Indicati Sulla di di del Connettore. I COLLEGAMENTI BCM Sono mostrati Nella foto qui sotto



Buona fortuna con il Progetto

Don

Mi Chiedo se Qualcuno qui Nella Comunità mi CONOSCE aiutare ad Attivare il Sensore pioggia / luce / umidita - 8U0 955 559 B al bene di operare la Manopola luci con posizione "Auto" - 5GG 941 431 D - ha aggiunto da me nel mio MK7 e ho Anche Messo Il Filo in piu Tra l'Interruttore e BCM per la Funzione Auto.


Ho attivato Tutte QUESTE Opzioni per VCD:


seleziona una
09-Cent. Elect.
Coding
5Q0-937-086 AK
Lungo Coding Helper
E Set:


Byte 6: Sensore di Luminosità installato (02) <- OK Attivazione
Byte 7: Interruttore con ADL installato (FB) <- OK Attivazione


di chiusura e Il ritorno alla Codifica, SI dovrebbe VEDERE un nuovo Elemento Nella Terza Posizione, o Il Nostro 8U0 955 559 B.
SCEGLIERE e codificatelo Così:
Byte 2: Audi A3 (6C)
da oggi il Sensore e Attivo.
Purtroppo non vedo this Terzo Elemento Che dovrebbe Attivare il Sensore con la BCM.


Aggiungo ALCUNE schermate:

[ferret vrs]

Hi guys

I just got a Ross-Tech cable.. Well actually got it for my Audi,
Though thought i might have a play with my Company car Golf also.

Though unlike the audi forum i can't find here a document that has all the cool vagcom
coding listed.

has anyone got a list of different vagcom codes that can be used that are tried and tested ?

Thanks

Tim

Hey mate, do you have a link to the Audi vag codes?
I have an B8 A4 that I would be keen to make some change on


Sent from my iPhone using Tapatalk

[AdamD]

Hey mate, do you have a link to the Audi vag codes?
I have an B8 A4 that I would be keen to make some change on

Have a look in the A4 section on ozAudi.com. There's also loads of info on audi-sport.net.

[DV52]

I wonder if anyone here in the Community I KNOW help Activate the rain / light / humidity sensor - 8U0 955 559 B for good to operate the knob lights with "Auto" position - 5GG 941 431 D - added by me in my MK7 and I Even put the wire in more Among the switch and BCM for the Auto function.


I activated All THESE Options for VCD:


select a
09-Cent. Elect.
Coding
5Q0-937-086 AK
Long Coding Helper
And Set:


Byte 6: Light sensor installed (02) <- OK Activation
Byte 7: Switch with installed ADL (FB) <- OK Activation


The closing and return to coding, you should see a new element in the Third Position, or Our 8U0 955 559 B.
CHOOSE and codificatelo So:
Byte 2: Audi A3 (6C)
now the sensor and Active.
Unfortunately I do not see this Third Element That should activate the sensor with the BCM.

Fabromix: Thanks for the PM. I had to translate your Italian to English - notwithstanding my Italian heritage, my Italian language skills are hopeless!

I'm not sure that there much more that I can add. The Rain-light-humidity sensors are a simple LIN bus circuit hanging-off the BCM -so not much to go wrong . Your settings for Byte 6 and Byte 7 look OK, the part number for the RLHS looks OK as well.

You should probably tell the Air Con controller @ address hex08 that the humidity side of the sensor is installed (Byte9, Bit 2-3 should be hex04) - but this is unlikely to be your problem.

Are you getting any error messages in the BCM? Have you checked that you are getting +12 Volts on Pin #1 of the RLHS (i.e. from fuse # 8 ) and have you confirmed that Pin #2 is actually earthed? Have you also checked the integrity of the LIN wire from Pin #3 on the RLHS to Pin #28, Socket C on the BCM?

Don

[fabbromix]

Ciao Don ti ho caricato alcuni screenshot di quello che mi dice il VCD.

[DV52]

Hello Don I loaded you some screenshots of what it tells me the VCDS.

fabbromix: your link is infected with a "severe" form of Trojan virus - I've only now reconfigured my laptop and reinstalled software - damn. I'm normally more careful about opening links, but this time too quick!!! - bummer

Anyhow -warning to others - DON'T OPEN FABBOMIX'S LINK!!


Don

[fabbromix]

I apologize ... for what has happened, I guarantee that file.zip is just a screenshot folder you from my PC while I was setting with Vag Com.
As soon as I can put only screnshot.


I'm sorry...

[nabaki]

fabbromix: your link is infected with a "severe" form of Trojan virus - I've only now reconfigured my laptop and reinstalled software - damn. I'm normally more careful about opening links, but this time too quick!!! - bummer

Anyhow -warning to others - DON'T OPEN FABBOMIX'S LINK!!


Don

Thanks...

Samsung'tan gönderildi...

[Faceman]

fabbromix: your link is infected with a "severe" form of Trojan virus - I've only now reconfigured my laptop and reinstalled software - damn. I'm normally more careful about opening links, but this time too quick!!! - bummer

Anyhow -warning to others - DON'T OPEN FABBOMIX'S LINK!!


Don

You may want to remove his link from your post.