Mk2 Tiguan VCDS Tweaks

[ajobbins]

Looked at that and some havent been able to get it to work

I read somewhere yesterday (can't find the link now) that you also have to have both the rear DRLs activated as well as the menu option for DRLs for this to work.

I haven't seen any details on what adaptation/coding achieves this to do it outside of the OBDEleven app...yet

[Guest001]

I read somewhere yesterday (can't find the link now) that you also have to have both the rear DRLs activated as well as the menu option for DRLs for this to work.

I haven't seen any details on what adaptation/coding achieves this to do it outside of the OBDEleven app...yet

Having the rears on as DRL's is called "Scandinavian" DRL and is on Autoinstructs Guides for the Tiguan list

[Moveingfaster]

I notice there is a new app in ODBEleven called "Turn Signals Blinking with Rear Light" that I don't think I've seen before. Has anyone done this to their Tiguan? Would it be legal to do in Oz?

VW Tiguan 2017 (Turn Signals Blinking With Rear Lights V1) - OBDeleven

VW Tiguan 2017- (Turn Signals Blinking With Rear Lights V2) - OBDeleven

[ATTACH=CONFIG]47983[/ATTACH]

I don’t think it’s for the LED tail lights in the US, it’s for the high level LED tail lights that the rest of the world gets.


Sent from my iPhone using Tapatalk

[Guest001]

I don’t think it’s for the LED tail lights in the US, it’s for the high level LED tail lights that the rest of the world gets.


Sent from my iPhone using Tapatalk

Weve got them in AUS. Rears with DRL's works here at least on Highlines

[ajobbins]

Having the rears on as DRL's is called "Scandinavian" DRL and is on Autoinstructs Guides for the Tiguan list

Yes, there are details to configure this which will hopefully then make the turn signal change to work. While there are details published on how to enable the Scandinavian DRLs through coding, there is no coding info I have found so far for the turn signals, just the OBDEleven app.

[SDST]

Has anyone tried the obdeleven app for "rear lid control" in an Allspace to enable you to close the boot from the drivers door switch?

"Turn ON or OFF function to close rear lid from remote or switch in the driver door" sounds right and figure it should be able to be enabled as its default on the 5 seater, but realise a few of the apps don't do what you expect...



edit: The thread on proboards was a bit inconclusive to my newbie brain. Suggests can be done, but only through making it think it's the 5 seater? Close rear lid with remote control | OBDeleven

[Guest001]

It was disabled (or not included) in the Allspace for safety reasons. Presumably so kids or rear row passengers would not get caught by the driver closing it without looking. Havent heard of it being able to be enabled in an Allspace

[Guest001]

Here is the coding to enable Rear DRL. This works on the LED Lights that come with the NZ R-Lines, not sure if it works with any other type of rear lights.

Central Electronic (09) - Adaptation - Leuchte16BLK SLB35BLK SL KC9 - Lichtfunktion B 16 - Change to Tagfahrlicht (Original Value: Parklicht rechts)

Central Electronic (09) - Adaptation - Leuchte17TFL R BLK SRB3TFL R BLK SR KC3 - Lichtfunktion B 17 - Change to Tagfahrlicht (Original Value: Parklicht links (beidseitiges Parklicht aktiviert li & re))

Central Electronic (09) - Adaptation - Leuchte23SL HLC10 - Lichtfunktion B 23 - Change to Tagfahrlicht (Original Value: Parklicht links (beidseitiges Parklicht aktiviert li & re))

Central Electronic (09) - Adaptation - Leuchte24SL HRA65 - Lichtfunktion B 24 - Change to Tagfahrlicht (Original Value: Parklicht rechts)

There is option in there to adjust the brightness as well however I haven't changed this setting as it will potentially make the park lights too bright at night time.

Going back along way but what is the setting to dim the tails if you have them on as DRl's in the daytime but have them normal at night

[PDMJO]

PSA: there's a new OBDeleven app which makes the start/stop button illumination fade in and out before you turn on the engine. very simple. very cool.

[Guest001]

PSA: there's a new OBDeleven app which makes the start/stop button illumination fade in and out before you turn on the engine. very simple. very cool.

Tried it yesterday Wasnt really impressed and turned it off again Might look ok at night but could barely see it in my garage..
did do the one that makes rears blink with the indicators and turned DRL"S off with handbrake.

[Hole46]

Tried it yesterday Wasnt really impressed and turned it off again Might look ok at night but could barely see it in my garage..
did do the one that makes rears blink with the indicators and turned DRL"S off with handbrake.

Which version did you use with the rears blinking with the indicators?


Sent from my iPad using Tapatalk

[Guest001]

Which version did you use with the rears blinking with the indicators?


Sent from my iPad using Tapatalk

2.................

[Ricka]

OK, posting in the correct thread now.
The link at the start of this thread shows 4 methods:
* Gateway Coding
* Prohibition
* Temperature
* Voltage

The first 3 methods have been blocked by VAG, even in our My19 Tig.

Only remaining option is Module 19, Byte 03, where it looks like you can untick the blue box for "Start/Stop system with recuperation installed (PR7L6)". Not game to try it without some knowledge that it is ok to do this. There is also a bit by bit alternative at that point.

Would be interested to know if anyone has tried it.

[Guest001]

OK, posting in the correct thread now.
The link at the start of this thread shows 4 methods:
* Gateway Coding
* Prohibition
* Temperature
* Voltage

The first 3 methods have been blocked by VAG, even in our My19 Tig.

Only remaining option is Module 19, Byte 03, where it looks like you can untick the blue box for "Start/Stop system with recuperation installed (PR7L6)". Not game to try it without some knowledge that it is ok to do this. There is also a bit by bit alternative at that point.

Would be interested to know if anyone has tried it.

I dont know why you cant turn it off with the voltage method. Mine is a Nov 2018 built MY 19 and I can do it in 20 secs
Are you using an OBD Eleven or something else

[Ricka]

I dont know why you cant turn it off with the voltage method. Mine is a Nov 2018 built MY 19 and I can do it in 20 secs
Are you using an OBD Eleven or something else

Using OBD11 Pro ie V2. I get error 31.