Electric seat dead after battery test

[Bezzey]

I got a front drivers seat from a 2019 Tiguan Highline and was testing it with direct power today with a battery. After using the position controls, I pressed one of the memory position buttons. The seat began moving to the memory position for about 1 second and then stopped. I did this a couple more times with the same response from all 3 position buttons.

I then went back to using the position controls and within a few seconds the seat went dead.

I've done the following:

• Tried a different battery
• Removed the controller circuit board to inspect for anything burned
• Disconnected each button control module 1 at a time
• Tested each motor with direct power - all ok

Have I fried the control board? Pics attached for reference.

[Guest001]

One thing to note with these seats is if you have it back beyond a certain point it wont return to its set place It also wont reverse for easy exit. Mine did it and VW put markers on side of seat to show where not to move it back past. Aslo wont work if voltage drops too far.

Dont know about a Tig but the base with all the gear in for a Passat is just over $1000

[Bezzey]

This is what I'm thinking has happened. I'm looking at the idea of wiring up the seat to my Amarok in order to access it with VCDS to clear faults/recalibrate or something like that.

[MIG]

My guess would be the seat controller is looking for a can bus signal to say the ignition is on something like the Klemmen_Status_01 on the MQB platform.

Do you have a scan tool? You can directly hook it up to the CAN high and low pins in the harness and see if it communicates.

Or you could try creating a test bench setup like in this thread Testbench setup? | Page 10 | Ross-Tech Forums

[Bezzey]

I have VCD and a OBD bluetooth dongle. If I identify the CAN pins on the seat control module and the OBD connection, can I communicate with it that way?

I will look into the test bench thread you linked.

[cameleon72]

I have VCD and a OBD bluetooth dongle. If I identify the CAN pins on the seat control module and the OBD connection, can I communicate with it that way?

I will look into the test bench thread you linked.

Hi
connect to OBD2 with VCDs and look and search for module 36 .

ECU: 0036 - Seat Adjustment Driver Side



See if you can log into DTC error any messages there. If you can access coding , adaptation of module 36 , than Can communication from driver seat to Car is fine and control module is responding to car gateway, But you my have some other problem which need to be addressed with special VW software only .
Regards

[Bezzey]

Where should I connect the module to my Amarok? Or is there way to connect directly to the seat module without a vehicle? Here is an old auto scan from my Amarok:

Saturday,13,February,2021,13:00:49:45971
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 20.12.0.1 (x64) HEX-V2 CB: 0.4529.4
Data version: 20201125 DS322.1
Ross-Tech: Home


VIN: WV1ZZZ2HZEA031608 License Plate: 1BC5BZ
Mileage: 211570km-131463mi Repair Order:

Chassis Type: 2H-VN81 (6N0)
Scan: 01 02 03 04 08 09 10 15 17 19 25 32 37 56 69 6C 0B

VIN: WV1ZZZ2HZEA031608 Mileage: 211570km-131463miles

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
15-Airbags -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
32-Differential Locks -- Status: OK 0000
37-Navigation -- Status: OK 0000
56-Radio -- Status: OK 0000
69-Trailer -- Status: Malfunction 0010
6C-Back-up Cam. -- Status: OK 0000
-------------------------------------------------------------------------------
Address 01: Engine (J623-CSHA) Labels:. 03L-906-022-CFC.clb
Part No SW: 03L 906 012 AF HW: 03L 907 309 AC
Component: R4 2,0L EDC H24 5936
Revision: 74H24--- Serial number: 00000000000000
Coding: 012A4012233600080001
Shop #: WSC 29131 001 1048576
ASAM Dataset: EV_ECM20BTD01103L906012AF 001009
ROD: EV_ECM20BTD01103L906012AF_001.rod
VCID: 6889BCFE92F8E27BDB2-803C

7 Faults Found:
4807 - EGR System
P0401 00 [096] - Insufficient Flow
Intermittent - Not Confirmed - Tested Since Memory Clear

12306 - Particulate Trap Bank 1
P2002 00 [096] - Efficiency Below Threshold
Intermittent - Not Confirmed - Tested Since Memory Clear

4814 - System Voltage
P0562 00 [032] - Too Low
Intermittent - Not Confirmed - Tested Since Memory Clear

10065 - Mass Air Flow Sensor (G70)
P0104 00 [032] - Intermittent
Intermittent - Not Confirmed - Tested Since Memory Clear

4881 - EGR Valve (N1
P1440 00 [032] - Open Circuit
Intermittent - Not Confirmed - Tested Since Memory Clear

9120 - EGR Sensor 1
P046C 00 [096] - Implausible Signal
Intermittent - Not Confirmed - Tested Since Memory Clear

4629 - ECM Power Relay Load Circuit
P068A 00 [032] - Opens Too Early
Intermittent - Not Confirmed - Tested Since Memory Clear

Readiness: 0 0 0 0 0

-------------------------------------------------------------------------------
Address 02: Auto Trans (J217) Labels:| 0CM-325-025.clb
Part No SW: 2H0 927 158 D HW: 0CM 325 025
Component: 2H0 20RTDIRdW H16 3001
Revision: --H16---
Coding: 000001
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_TCMAL450211 002011
ROD: EV_TCMAL450211_002_VN81.rod
VCID: 2E050AE6709C7C4BD1E-807A

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes (-----) Labels: None
Part No SW: 2H0 907 379 M HW: 2H0 907 379 D
Component: ESP MK25A XT H44 0111
Revision: 00H44001
Coding: C07324B69997039624A899A3AF58F0
Shop #: WSC 07456 790 49164
VCID: 3A2D36B6BC54A0EB7D6-806E

No fault code found.

-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 7E5-907-040.clb
Part No SW: 2H0 907 040 E HW: 2H0 907 040 E
Component: ClimatronicT5 H19 0406
Revision: 00001003
Coding: 0000000002
Shop #: WSC 07456 790 50316
ASAM Dataset: EV_ClimatronicT5 A01003
ROD: EV_ClimaAutoT5Basis.rod
VCID: 2313EBD22B5EC1234E0-8076

No fault code found.

-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519) Labels:. 7H0-937-08x-09.clb
Part No SW: 7H0 937 090 B HW: 7H0 937 090
Component: BCM PQ25 Max4 H74 0712
Revision: B9074001 Serial number: 0571 263130671
Coding: 240002380C61040093380E302CCB86C50F80610F6080204130 0000020003
Shop #: WSC 29131 001 1048576
VCID: 2D070DEA7D1A0753E84-8078

Subsystem 1 - Part No: 1K0 955 559 AH Labels: 1K0-955-559-AG.CLB
Component: RLS 231013 05 54 0403
Coding: 02302D

Subsystem 2 - Part No SW: 6R0 959 802 M HW: 6R0 959 802 M Labels: 6R0-959-802.CLB
Component: J386__TSG_FT 002 3323
Serial number: --------------------
Coding: 050000

Subsystem 3 - Part No SW: 6R0 959 801 P HW: 6R0 959 801 P Labels: 6R0-959-801.CLB
Component: J387__TSG_BT 002 3323
Serial number: --------------------
Coding: 050000

Subsystem 4 - Part No: 1K8 951 171 A
Component: DWA-Sensor 00 001 0103
Coding: 000000

Subsystem 5 - Part No: 1K8 951 605 B
Component: LIN BACKUP HO H11 9005
Coding: 000000

Subsystem 6 - Part No: 1K8 951 171 A
Component: DWA-Sensor 00 001 0103
Coding: 000000

Subsystem 7 - Part No SW: 5K0 959 542 C HW: 5K0 959 542 C
Component: E221__MFL-TAS H31 0037
Serial number: 0304767
Coding: 820000

Subsystem 8 - Part No SW: 6R0 959 811 D HW: 6R0 959 811 D
Component: J388__TSG_HL 002 3323
Serial number: --------------------
Coding: 000000

Subsystem 9 - Part No SW: 6R0 959 812 D HW: 6R0 959 812 D
Component: J389__TSG_HR 002 3323
Serial number: --------------------
Coding: 000000

No fault code found.

-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J446) Labels:| 7E0-919-475.clb
Part No SW: 7E0 919 475 L HW: 7N0 919 475
Component: PARKHILFE 8K H06 0106
Revision: -------- Serial number: 28261329903763
Coding: 318103
Shop #: WSC 29131 001 104857
ASAM Dataset: EV_VW75XParkAssis8K 001003
ROD: EV_VW75XParkAssis8K_001_VN75.rod
VCID: 3B2333B2B3EE99E3660-806E

No fault code found.

-------------------------------------------------------------------------------
Address 15: Airbags (J234) Labels:| 5K0-959-655.clb
Part No SW: 2H0 959 655 B HW: 2H0 959 655 B
Component: VW10Airbag00H H07 0013
Revision: -------- Serial number: 003HN00EWKT9
Coding: 000000000000000000000000000000003048
Shop #: WSC 07446 790 50316
ASAM Dataset: EV_AirbaVW10BPAVN750 A01026
ROD: EV_AirbaVW10BPAVN750.rod
VCID: 33331B929BBE51A3BE0-8066

Crash sensor for side airbag: driver side:
Serial number: 3495RRB401I50O3MRHME

Front Passenger's Side Airbag Crash Sensor:
Serial number: 3505RRB401850O3MB0QA

Crash sensor for front airbag: driver side:
Serial number: 3555YRB400M50FMEQGUT

Crash sensor for front airbag: front passenger side:
Serial number: 3565YRB400M50FMEP9ME

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels:| 5K0-920-xxx-17.clb-SRI1
Part No SW: 2H0 920 871 HW: 2H0 920 871
Component: KOMBI H04 0709
Serial number: 00000000000000
Coding: 151A00
Shop #: WSC 07456 000 09999
ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04723
ROD: EV_Kombi_UDS_VDD_RM09_004_VW36.rod
VCID: 6597B5CA65EAFF13E04-8030

No fault code found.

-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels:. 6N0-909-901-6R.clb
Part No SW: 6N0 909 901 HW: 7H0 937 090
Component: GW-K-CAN TP20 H74 0712
Revision: B9074001
Coding: 742300
Shop #: WSC 29131 001 1048576
VCID: 70B9D49EAAA82ABB832-8024

No fault code found.

-------------------------------------------------------------------------------
Address 25: Immobilizer (J334) Labels:| 5K0-920-xxx-25.clb
Part No SW: 5K0 953 234 HW: 5K0 953 234
Component: IMMO H04 0709
Serial number:
Coding: 000000
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03710
ROD: EV_Immo_UDS_VDD_RM09_VW23.rod
VCID: 6A8DC6F68CF4D06BCD6-803E

No fault code found.

-------------------------------------------------------------------------------
Address 32: Differential Locks (J647) Labels:* 2H0-927-771.clb
Part No SW: 2H0 927 771 A HW: 2H0 927 771
Component: Quersperre H04 0017
Revision: 11001001 Serial number: 4DG 16.10.13 00
Coding: 000001
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_QuersUDSAAMVN817 A01606
ROD: EV_QuersUDSAAMVN817.rod
VCID: 2C0100EE46800E5BFFA-8078

No fault code found.

[Bezzey]

Continued below...

-------------------------------------------------------------------------------
Address 37: Navigation (J794) Labels:| 1K0-035-27x-37.clb
Part No SW: 3C8 035 279 K HW: 3C8 035 279 K
Component: RNS315-EU H78 0408
Serial number: VWZAZ2S0986357
Coding: 000004110200160000031002
Shop #: WSC 10314 002 1048576
ASAM Dataset: EV_RNS315EUV2UDS 001705
ROD: EV_RNS315EUV2UDS.rod
VCID: 33331B929BBE51A3BE0-8066

Data carrier:
Subsystem 1 - Part No: 3AA 919 866 E
Component: AUS_V1 0043

No fault code found.

-------------------------------------------------------------------------------
Address 69: Trailer (J345) Labels:. 1K0-907-383-V2.clb
Part No SW: 1K0 907 383 F HW: 1K0 907 383 F
Component: Anhaenger H09 0100
Revision: 3A001001 Serial number: 00008030467966
Coding: 0100000100000000
Shop #: WSC 00000 000 00000
VCID: 3039149E6A286ABBC32-8064

2 Faults Found:
02563 - Trailer; Right Tail Lamps (M61)
010 - Open or Short to Plus - MIL ON
Freeze Frame:
Fault Status: 11101010
Fault Priority: 3
Fault Frequency: 1
Reset counter: 154
Mileage: 210779 km
Time Indication: 0
Date: 2015.06.22
Time: 19:06:08

02564 - Trailer; Left Tail Lamps (M60)
010 - Open or Short to Plus - MIL ON
Freeze Frame:
Fault Status: 11101010
Fault Priority: 3
Fault Frequency: 1
Reset counter: 154
Mileage: 210779 km
Time Indication: 0
Date: 2015.06.22
Time: 19:06:08


-------------------------------------------------------------------------------
Address 6C: Back-up Cam.
Cannot be reached

End----------(Elapsed Time: 02:35, VBatt start/end: 12.1V/12.1V)-----------

[MIG]

You can connect directly to the module; my first bench setup was a cheap OBD female connector and hooked up the following pinout.

4, 5 = Gnd
16 = Bat+
6 = CAN H
14 = CAN L


You can tell the CAN wires are coloured (orange with a colour band = CAN H) (orange with a brown band = CAN L)

[Bezzey]

I've ordered this cable:

iKKEGOL 1ft Feet 30cm/12 16 Pin J1962 OBD OBDII OBD2 Female Connector Car Diagnostic Extension Cable Cord Pigtail DIY Mobley Adapter https://amzn.asia/d/cZuSa3s

[Bezzey]

You can connect directly to the module; my first bench setup was a cheap OBD female connector and hooked up the following pinout.

4, 5 = Gnd
16 = Bat+
6 = CAN H
14 = CAN L


You can tell the CAN wires are coloured (orange with a colour band = CAN H) (orange with a brown band = CAN L)

I have successfully connected directly to the seat module using this female OBD connector:
https://www.amazon.com.au/dp/B07F16HC12?ref=ppx_yo2ov_dt_b_product_details&th=1


This is probably well known be experienced members here, but I had to select the seat module directly under Select Control Module.


This is my initial scan:

Friday,26,May,2023,21:27:33:45971

[COLOR=#141414][FONT=Verdana]VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]VCDS Version: 22.9.0.0 (x64)  HEX-V2 CB: 0.4623.4[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]Data version: 20220830 DS341.0[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]www.Ross-Tech.com[/FONT][/COLOR][COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]VIN: WVGZZZ5NZKW833436   License Plate:[/FONT][/COLOR][COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]--------------------------------------------------------------------------------[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]--------------------------------------------------------------------------------[/FONT][/COLOR][COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                Address 36: Seat Mem. Drvr[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]Control Module Part Number: 5Q0 959 760 C[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]  Component and/or Version: Sitzmemory    H09 0024[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]           Software Coding: 001400020000050001C280808180000000008181000000F400[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Work Shop Code: WSC 12345[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                      VCID: 3D273DAAADFA97D3CC5-8068[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]Advanced Identification/FAZIT[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Serial number: Y0006RJJ39570[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Identification: KO1-ABY[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Date: 19.10.18[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Manufacturer number: 3201[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Test stand number: 9570[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]Flash Status[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Programming Attempts(application): 0/0[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Programming Attempts(data): 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Successful Attempts(data): 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Flash Date: 00.01.01[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Flash Tool Code(data): 40022 666 40022[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]Misc.[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Hardware number: 5Q0 959 760 C[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Workshop System Name: J810[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Equipment/PR Code: 000000000000000000000000[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Dataset Number: -----------[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     Dataset Version: ----[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     ASAM Dataset: EV_SeatMemorDriveSide[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]     ASAM Dataset Revision: 002022[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]VCDS Info:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]       VCID: 3D273DAAADFA97D3CC5-8068[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]       Labels: NONE[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]       ROD: EV_SeatMemorDriveSide.rod[/FONT][/COLOR]

Under Basic Settings, there are 3 options:

1. IDE02325-MAS00675-Reset to factory setting
2. IDE02854-MAS00675-Reset standardization
3. MAS05563-MAS00675-Norming

I am reluctant to perform reset to factory settings as I've read other people having headaches when doing this.


I have performed IDE02854-MAS00675-Reset standardization on all seat motors successfully.


When I first tried MAS05563-MAS00675-Norming, I got the following error: ERROR: Vehicle speed too high. This was easily fixed by going to Adaptations and changing ENG123066-vehicle_velocity_monitoring from active to not active. Now when I try Norming, I get the following error: ERROR: Conditions not correct or request sequence error.


When I go into Output Tests and try each option to manually operate the motors, I get the following errors:

[Bezzey]

These are the faults that persist:

 Saturday,27,May,2023,00:49:32:45971

[COLOR=#141414][FONT=Verdana]VCDS Version: Release 23.3.1 (x64) Running on Windows 10 x64[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]www.Ross-Tech.com[/FONT][/COLOR][COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]               Address 36: Seat Mem. Drvr       Labels: NONE[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]Control Module Part Number: 5Q0 959 760 C    HW: 5Q0 959 760 C[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana] Component and/or Version: Sitzmemory    H09 0024[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]          Software Coding: 001400020000050001C280808180000000008181000000F400[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]           Work Shop Code: WSC 12345 123 61029[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]             ASAM Dataset: EV_SeatMemorDriveSide 002022 (VW37)[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                      ROD: EV_SeatMemorDriveSide.rod[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                     VCID: 3D273DAAADFA97D224D-8068[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]7 Faults Found:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]9655636 - Motor for Seat Fore/Aft Adjustment[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         B1355 54 [009] - Missing Calibration / Basic Setting[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         Confirmed - Tested Since Memory Clear[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Freeze Frame:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Status: 00000001[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Priority: 4[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Frequency: 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Reset counter: 81[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Date: 2000.00.00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Time: 00:00:00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]9655892 - Motor for Seat Backrest Adjustment[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         B1356 54 [009] - Missing Calibration / Basic Setting[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         Confirmed - Tested Since Memory Clear[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Freeze Frame:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Status: 00000001[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Priority: 4[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Frequency: 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Reset counter: 81[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Date: 2000.00.00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Time: 00:00:00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]9655380 - Motor for seat height adjustment[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         B1354 54 [009] - Missing Calibration / Basic Setting[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         Confirmed - Tested Since Memory Clear[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Freeze Frame:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Status: 00000001[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Priority: 4[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Frequency: 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Reset counter: 81[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Date: 2000.00.00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Time: 00:00:00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]9655124 - Motor for Seat Tilt Adjustment[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         B1353 54 [009] - Missing Calibration / Basic Setting[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         Confirmed - Tested Since Memory Clear[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Freeze Frame:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Status: 00000001[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Priority: 4[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Frequency: 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Reset counter: 81[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Date: 2000.00.00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Time: 00:00:00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]9654868 - Motor for Lumbar Support Fore/Aft Adjustment[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         B1352 54 [009] - Missing Calibration / Basic Setting[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         Confirmed - Tested Since Memory Clear[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Freeze Frame:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Status: 00000001[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Priority: 4[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Frequency: 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Reset counter: 81[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Date: 2000.00.00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Time: 00:00:00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]9654612 - Motor for Lumbar Support Height Adjustment[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         B1351 54 [009] - Missing Calibration / Basic Setting[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         Confirmed - Tested Since Memory Clear[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Freeze Frame:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Status: 00000001[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Priority: 4[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Frequency: 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Reset counter: 81[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Date: 2000.00.00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Time: 00:00:00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]
[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]10489856 - No Basic Setting[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         B2010 00 [009] - -[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         [keine oder falsche Grundeinstellung/Adaption][/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]         Confirmed - Tested Since Memory Clear[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]            Freeze Frame:[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Status: 00000001[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Priority: 7[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Fault Frequency: 1[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Reset counter: 81[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Date: 2000.00.00[/FONT][/COLOR]
[COLOR=#141414][FONT=Verdana]                   Time: 00:00:00[/FONT][/COLOR]

[MIG]

I should have mentioned you needed to select the module when you don't have a gateway in the mix.

Check the advance measuring values; my guess is the seat is missing a signal it wants from the rest of the car before enabling the motors, just like you had with the speed too high warning.


At least you know the controller is good.

[Bezzey]

I should have mentioned you needed to select the module when you don't have a gateway in the mix.

Check the advance measuring values; my guess is the seat is missing a signal it wants from the rest of the car before enabling the motors, just like you had with the speed too high warning.


At least you know the controller is good.

I purchased another set of seats yesterday from another wreckers, both full electric with memory and the R-Line emblem.

From here on, I will refer to them as:

Seat 1: The seat I have working with so far. From Tiguan 1. Appears to be the same as R-Line just no emblem or white stitching. Full electric with memory buttons.

Seat 2: The drivers seat from Tiguan 2. R-Line emblem, white stitching full electric with memory buttons.

Seat 3: The passenger seat from Tiguan 2. R-Line emblem, white stitching full electric with memory buttons.

I have compared the advanced measuring values between Seat 1, Seat 2 & Seat 3. The only difference in advanced measuring values I have found is this:

Seat 1:

IDE01457 Energy management deactivation stage Deactivation stage 3

Seat 2:

IDE01457 Energy management deactivation stage Deactivation stage 0

Seat 3:

IDE01457 Energy management deactivation stage Deactivation stage 0

Seat 1 is still not operational with the following faults:

9655636 - Motor for Seat Fore/Aft Adjustment B1355 54 [009] - Missing Calibration / Basic Setting
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 81
Date: 2000.00.00
Time: 00:00:00

9655892 - Motor for Seat Backrest Adjustment
B1356 54 [009] - Missing Calibration / Basic Setting
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 81
Date: 2000.00.00
Time: 00:00:00

9655380 - Motor for seat height adjustment
B1354 54 [009] - Missing Calibration / Basic Setting
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 81
Date: 2000.00.00
Time: 00:00:00

9655124 - Motor for Seat Tilt Adjustment
B1353 54 [009] - Missing Calibration / Basic Setting
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 81
Date: 2000.00.00
Time: 00:00:00

9654868 - Motor for Lumbar Support Fore/Aft Adjustment
B1352 54 [009] - Missing Calibration / Basic Setting
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 81
Date: 2000.00.00
Time: 00:00:00

9654612 - Motor for Lumbar Support Height Adjustment
B1351 54 [009] - Missing Calibration / Basic Setting
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 81
Date: 2000.00.00
Time: 00:00:00

10489856 - No Basic Setting
B2010 00 [009] - -
[keine oder falsche Grundeinstellung/Adaption]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 7
Fault Frequency: 1
Reset counter: 81
Date: 2000.00.00 Time: 00:00:00

Seat 2 is operational with the following faults:

9655636 - Motor for Seat Fore/Aft Adjustment B1355 54 [009] - Missing Calibration / Basic Setting
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 228
Mileage: 68276 km
Date: 2023.03.04
Time: 15:26:26


10489856 - No Basic Setting
B2010 00 [009] - -
[keine oder falsche Grundeinstellung/Adaption]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 7
Fault Frequency: 1
Reset counter: 228
Mileage: 68276 km
Date: 2023.03.04
Time: 15:26:26

Seat 3 I have not operated any of the buttons yet. No faults present.

Edit: I have operated Seat 3 (except for the memory buttons) and still no fault codes. I have noticed an extra option under Basic Settings that is not on Seat 1 & Seat 2:

IDE02404-MAS00675-Checksum calculation

[Bezzey]

No wonder I am getting faults still...the module has, for some reason decided that the maximum and minimum travel values are the same. Not to mentioned the supposed current position of all the motors is exactly the same down to 1 step accuracy and outside the max/min range.

Any idea on how to correct this? I've tried numerous attempts of IDE02854-MAS00675-Reset standardization & MAS05563-MAS00675-Norming. Reset standardization passes instantly and Norming comes back with the following error: ERROR: Conditions not correct or request sequence error.