ACC Retrofit Advice Please for Golf MK7

[guile]

Hi all

I’m covering a basic write up on another thread regarding mods to my Golf MK7 PP DSG, including this ACC retrofit. I’m going to tidy that thread up as I go to try and provide easy to follow steps for anyone else that wants to do the ACC retrofit…

I’ve been doing hours or reading on this and I’m still not 100% sure I understand what I need to do so I thought I’d check with the experts if you wouldn’t mind reviewing the below and picking me up on anything I’ve misunderstood. A lot of threads had info from Don (thanks Don) and I acknowledge that some of his material is included below along with XaGiCo Dossier (link below)…

Dropbox - XaGiCo DOSSIER VCDS VW GOLF MKVII 1.5.pdf - Simplify your life

I haven’t organised component protection removal yet. I have called euro car electrics on the Sunny Coast 3 times but couldn’t get through (they charge $300); next stop is VW Newstead in Brisbane. I’m toying with the idea of buying the VNCI 6154A tool but I think it could end up being a waste of money if I don’t know how to use it. I do know you can buy single uses of ODIS but don’t really understand how that works. If anyone else has suggestions for component protection removal I’d appreciate it please…

Parts that I have bought already:
Front bumper centre grille with radar hole – 5G0853677D
ACC radar plug and loom – 4F0972708
MFSW steering wheel switches – 5G0959442N
Bosch Long Range Radar (LRR) – 5Q0907541J

My install sequence plan:
1. Remove front bumper and drill existing bumper iron to mount the radar
2. Mount the radar with less than 0.2 degrees angle and refit bumper with new grille
2. Route the wiring loom around the inside of the engine bay to behind the battery
3. Feed the loom through the grommet in the firewall to the passenger footwell
4. Connect the positive for the ACC to the fuse box and negative to a ground stud
5. Connect the CAN-Bus to the black TUIL connector as noted below:
Or/Br -> CAN-Bus Extended Low -> Pin 3 on Radar
Grey -> CAN-Bus Extended High -> Pin 2 on Radar
6. Remove the existing steering wheel buttons and install the new ones
7. Hope and pray that was all done correctly

Now the fun part, coding:
01 – Engine
Set ACC with Front Assist ( PR-8T3, PR-8T8 )
03 – ABS (coding for 29 bit) you need to edit bit 24:
Set F8
09 – Gateway
Add 13 – Auto Dist. Reg on the installation list
Under Adaptation change steering wheel type to ACC
17 – Instrument
On the cluster set all the ticks for Front Assist and Distance Regulation
5F – Radio
Set all the ticks for Front Assist, ACC and PreCrash
A5 – Front Camera
Set presence of ACC
13 – Radar
Set presence of ACC

This where I get a bit confused due to the following:
1. The security access code (20103) that XaGiCo dossier mentions; is that just to allow me to make changes.
2. ABS - how do I “Set F8”. From XaGiCo dossier it’s a set of 0 and 1 that need to be changed. Also do I have to change anything on byte 26.
3. CAN-Gateway - minor detail but is it 09 or 19 (I don’t have my car or VCDS with me at the moment)
4. Radio - do I also need to tick all AWV options as per XaGiCo dossier
5. Front Camera - my car doesn’t have a front camera as far as I know. Is this an issue.
6. Radar - XaGiCo dossier talks about setting Front Assist Camera and Trailer Recognition. Is this necessary.
7. XaGiCo dossier has a coding step involving the need for ODIS (Funktion_ACC). Is this necessary.

Thanks in advance!

[Guest001]

Eurocarupgrades are possibly shut for the holidays .

[guile]

Ok thanks, I wondered the same thing. I’ll try again next week…

[DV52]

First - where did you buy the LRR - or more particularly, does it have the correct dataset for this car? Have you read THIS?

Questions:
1 -security code ONLY needed if you want to make changes to coding values on new hex13 module (only needed for some adaptation channels)
2 -Assuming that this car has a MK100 ABS module (with a 30 x Byte long-code string) I think the change needs to be made to Byte 24 (not Byte 29). Change Bit 2=1 and Bit 4=1
3 The address for the CAN Gateway is 19 (not 09)
5 No, lots of earlier mk7s didn't have the front camera installed with ACC
6 See response 5 about front camera - does this car have a trailer module (@ address hex69)?

Don

[guile]

thanks for the reply Don…

I bought the LLR from a wreckers and yes I’ve read that web page. As far as I'm aware 5Q0907541J supersedes 5Q0907541G...

I’m not home for a week so will need to confirm ABS model etc then. See below screenshot of coding from XaGiCo dossier...



I doubt it has a trailer module as it has no towbar so I guess I just don't tick the Trailer Recognition box...

Do you know what the ODIS coding of Funktion_ACC is for on XaGiCo dossier, as per the screenshot below...

[DV52]

Yes, as confirmed in the first of your pictures, the correct modification to tell the ABS module that you have added the ACC module is on Byte 24 (not Byte 29).

I'm not quite convinced about the value of either F4 (for manual), or F8 (for DSG) - but both XaGiCo and my link suggest these values, so go with it!!

As for the second picture, I first need to explain numbering theory (a little) - my apology if you already know this stuff.

A Byte consists of 8 x Bits. Each Bit is independent of the other Bits. I think of a Bit as a software switch meaning that a Bit can have one of two states- being either ON, or OFF (just like a normal mechanical switch) - or 1, or 0. However, unlike a normal switch, the status of a Bit is changed by a software command rather than a mechanical lever, or button

By convention, the Bits are numbered 0, 1, 2..........7 and the complete string of 8 x Bits make-up a Binary number. It's possible to convert Binary numbers into equivalent values in other counting systems. For example, there is an equivalence of a Binary number in the normal decimal system of counting and there is also an equivalence in hexadecimal (hex) numbers - which use a base 16 counting system. The values in XaGiCo pictures, F4 and F8 are hexadecimal numbers

Again by convention, the Bits in a Binary number are read from right-to-left - meaning that the right-most digit is Bit 0 and the left-most digit is Bit 7.

Here's an example: the hexadecimal number F4 is equal to the Binary number 1111 0100. So the last digit on the right in the Binary number is Bit 0 (which is equal to 0) and the left most digit is Bit 7 (which is equal to 1)

Hopefully you are still following!

In the second picture, Byte 26 =hex50=0101 0000. So, the instructions suggest that Bit 6=1 and Bit 4=1. According to my information, this means that you are telling the ABS module that the car is fitted with Bi-Directional Wheel Speed Sensors (Multi-Link Rear Suspension). ACC needs these type of speed sensors to operate correctly - I'm not sure what happens if you tell-porkies to the ABS module about this matter!




I'm not a user of VAS5054 - but my guess is that the screenshot shows how to use the "guided-function" feature to implement the coding changes. The "guided function" facility is the forerunner of a similar feature that was copied by OBDeleven in their One Click Apps - it's an inbuilt software function that automatically implements all coding changes across each module without the need for the individual steps when using VCDS, or OBD11

So the screenshot shows an alternative way of implementing the ACC coding changes - it doesn't show an additional coding change that's needed in the retrofit exercise!

[guile]

Great, thanks again Don…

I think I’ve got enough info to give the coding a go now…

The final piece of the puzzle is to get cp removed…

[DV52]

If you take the car to a dealer, removing CP should cost the minimum time for a master-tech - which is normally 1 x hour. It shouldn't take anywhere near 60 minutes for a half-competent master-tech - but dealers don't use clocks to measure chargeable time -instead they use the monopoly principle of squeezing the client's wallet!!

The last time a friend threw money at a dealer to remove CP, it cost $250- outrageous!!

Don

[guile]

I managed to get time to fit the parts on the weekend and have a crack at the coding...

some of the codes were not accepted which is a bit concerning but i'm hoping that can be rectified once the component protection is removed...







one of the control modules couldn't be reached, 5F: Information Electr. I'm guessing thats because i've replaced the head unit with an Android one. Hope this won't be a problem when trying to finalise the coding...

[guile]

Sun 2024-01-21 10:16 AM
Sunday,21,January,2024,09:18:50:54062
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 8.1 x64
VCDS Version: 21.9.0.2 (x64)
Data version: 20210903 DS330.0
Ross-Tech: Home


VIN: WVWZZZAUZFW270452 License Plate: INK10
Mileage: 178137km-110689mi Repair Order:



--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Chassis Type: AU-VW37 (5Q0)
Scan: 01 02 03 08 09 10 13 14 15 16 17 19 32 42 44 52 55 5F A9

VIN: WVWZZZAUZFW270452 Mileage: 178137km-110689miles

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: Malfunction 0010
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
10-Park/Steer Assist -- Status: OK 0000
13-Auto Dist. Reg -- Status: Malfunction 0010
14-Susp. Elect. -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
32-Differential Locks -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
55-Headlight Range -- Status: OK 0000
5F-Information Electr. -- Status: Malfunction 0010
A9-Struct. Borne Sound -- Status: OK 0000

-------------------------------------------------------------------------------
Address 01: Engine (J623-CHHA) Labels:. 06K-907-425-V1.clb
Part No SW: 5G0 906 259 HW: 06K 907 425 B
Component: 2.0l R4 TFSI H13 0010
Revision: --H13--- CVN: 5FBD913B
Coding: 091D00324464050B2000
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_ECM20TFS0215G0906259 001014
ROD: EV_ECM20TFS0215G0906259.rod
VCID: 6BD5C38F8256DED184-803E
VINID: 9E69EAAAA465A969C21C0105082C00D17E

No fault code found.
Readiness: 1110 0001

-------------------------------------------------------------------------------
Address 02: Auto Trans (J743) Labels: 0D9-927-770.clb
Part No SW: 0D9 300 020 G HW: 02E 927 770 AQ
Component: DQ250-6V MQB H53 4520
Revision: 03253104 Serial number: TFK01502080055 CVN: 0000B2F1
Coding: 0014
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_TCMDQ250021 001001
ROD: EV_TCMDQ250021.rod
VCID: 1939C947184A9C41A6-804C

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104) Labels: 5Q0-907-379-IPB-V1.clb
Part No SW: 3Q0 907 379 Q HW: 3Q0 907 379 F
Component: ESC H42 0610
Revision: 00000000 Serial number: 60385000000728
Coding: 01FA93A15427296C077B060541C56980C92A94E0608296F700 4200B9C209
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_Brake1UDSContiMK100IPB 034036
ROD: EV_Brake1UDSContiMK100IPB_034.rod
VCID: 489F5C03F360D5C9C9-801C

1 Fault Found:
8314 - Check Coding of ECUs on Powertrain Data Bus
P1647 00 [009] - -
[New feature! Extended UDS fault detail is only supported by
current gen. interfaces]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 2
Reset counter: 87
Date: 2024.01.21
Time: 09:07:27


-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 5G0-907-044.clb
Part No SW: 5G0 907 044 BC HW: 5G0 907 044 BC
Component: Climatronic H03 1001
Revision: 00001K08
Coding: 00120004200100001005000012101400
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_ACClimaBHBVW37X 003018
ROD: EV_ACClimaBHBVW37X_003_VW37.rod
VCID: 69D9B98788AACCC1F6-803C

Fresh air blower control module (front):

A/C pressure/coolant temperature sensor:

Air quality sensor:

No fault code found.

-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519) Labels:| 5Q0-937-08X-HV1.clb
Part No SW: 5Q0 937 084 AJ HW: 5Q0 937 084 AJ
Component: BCM MQBAB H H18 0137
Serial number: 01011504503381
Coding: 03001A42C24122FB0BA44080B10C0728100000000000000000 0000000000
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_BCMCONTI 013000
ROD: EV_BCMBOSCH_013.rod
VCID: 000F84239BD02D8941-8054

Wiper motor control module:
Subsystem 1 - Part No SW: 5G2 955 119 A HW: 5G2 955 119 A
Labels: 5QX-955-119-V1.CLB
Component: WWS 150202 042 0551
Serial number: 150207073710
Coding: 0E4DDD

Rain/Light Recognition Sensor:
Subsystem 2 - Part No SW: 5Q0 955 547 A HW: 5Q0 955 547 A
Labels: 5Q0-955-547.CLB
Component: RLHS 037 0059
Serial number: S5Y15M02D16H19M45S23
Coding: 00A8DD

Anti-theft alarm system sensor:
Subsystem 3 - Part No SW: 5Q0 951 172 HW: 5Q0 951 172
Component: Sensor, DWA 005 0315
Serial number: 000000000ZY1502342Z9

Alarm horn:
Subsystem 4 - Part No SW: 5Q0 951 605 HW: 5Q0 951 605
Component: Sirene, DWA 004 0311
Serial number: 00000000000061644739

No fault code found.

-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J791) Labels:| 5Q0-919-294.clb
Part No SW: 5Q0 919 294 E HW: 5Q0 919 294 A
Component: PARKHILFE 8K H03 0048
Revision: -------- Serial number: 39391504217542
Coding: 0031151011
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_EPHVA18AU3700000 002024
ROD: EV_EPHVA18AU3700000_002_VW37.rod
VCID: 3D713DD7ACA280616A-8068

No fault code found.

-------------------------------------------------------------------------------
Address 13: Auto Dist. Reg (J42 Labels:| 5Q0-907-567.clb
Part No SW: 5Q0 907 567 J HW: 5Q0 907 567 J
Component: ACC3 H09 0395
Serial number: 23061375030055
Coding: 001E1300FE030B
Shop #: WSC 00028 028 00023
ASAM Dataset: EV_ACCBoschMQB 001022
ROD: EV_ACCBoschMQB_VW37.rod
VCID: 428B4E2BD55CFF9917-8016

3 Faults Found:
15360768 - Component Protection
U1101 00 [047] - Active
[New feature! Extended UDS fault detail is only supported by
current gen. interfaces]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 87
Mileage: 178137 km
Date: 2024.01.21
Time: 09:07:27

Control Module temperature: 37 °C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s²

1043 - Automatic Distance Control
B10E7 F0 [047] - Disconnected
[New feature! Extended UDS fault detail is only supported by
current gen. interfaces]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 87
Mileage: 178137 km
Date: 2024.01.21
Time: 09:07:27

Control Module temperature: 37 °C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s²

1058 - Databus
U1123 00 [047] - Received Error Message
[New feature! Extended UDS fault detail is only supported by
current gen. interfaces]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 87
Mileage: 178137 km
Date: 2024.01.21
Time: 09:07:29

Control Module temperature: 37 °C
Voltage terminal 15: 12.3 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s²


-------------------------------------------------------------------------------

[guile]

-------------------------------------------------------------------------------
Address 14: Susp. Elect. (J250) Labels: 5Q0-907-376.clb
Part No SW: 5Q0 907 376 HW: 5Q0 907 376
Component: DAEMPFUNGS-SG H16 0115
Serial number: 19011541350032
ASAM Dataset: EV_DRCONTITEMIC 001019
ROD: EV_DRCONTITEMIC_VW37.rod
VCID: 76E3E2FBC91413396B-8022

No fault code found.

-------------------------------------------------------------------------------
Address 15: Airbags (J234) Labels:| 5Q0-959-655.clb
Part No SW: 5Q0 959 655 D HW: 5Q0 959 655 D
Component: AirbagVW20 014 0385
Serial number: 003F6R0G6FAC
Coding: 98CCC000000000005C00000000C800000065
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_AirbaVW20SMEVW37X 002130
ROD: EV_AirbaVW20SMEVW37X_VW37.rod
VCID: 41894127D05AE4810E-8014

Crash sensor for side airbag: driver side:
Subsystem 1 - Part No SW: ----------- HW: 480 001 102 15
Component: SideSensor_Df 001 0887
Serial number: 3576700000060274E21L
Coding: 2D2D2D

Front Passenger's Side Airbag Crash Sensor:
Subsystem 2 - Part No SW: ----------- HW: 480 001 102 15
Component: SideSensor_Pf 001 0887
Serial number: 3586700000036134E21K
Coding: 2D2D2D

Rear Side Airbag Crash Sensor (on driver's side):
Subsystem 3 - Part No SW: ----------- HW: 480 400 602 15
Component: SideSensor_Dr 001 6149
Serial number: 3516502A1196FF53D06K
Coding: 2D2D2D

Passenger side rear thorax airbag crash sensor:
Subsystem 4 - Part No SW: ----------- HW: 480 400 602 15
Component: SideSensor_Pr 001 6149
Serial number: 3526502BB196FF54804Q
Coding: 2D2D2D

Crash sensor for front airbag: driver side:
Subsystem 5 - Part No SW: ----------- HW: 480 400 502 15
Component: FrontSensor_D 001 6149
Serial number: 3556502C5192BC734039
Coding: 2D2D2D

No fault code found.

-------------------------------------------------------------------------------
Address 16: Steering wheel (J524) Labels:| 5Q0-953-549.clb
Part No SW: 5Q0 953 521 P HW: 5Q0 953 569 A
Component: Lenks.Modul 075 0175
Revision: FF032032 Serial number: 20150212400803
Coding: 0410
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_SMLSVALEOMQB 001015
ROD: EV_SMLSVALEOMQB.rod
VCID: 3F8D47DFA6AE927178-806A

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels:| 5G0-920-XXX-17.clb-SRI3
Part No SW: 5G1 920 756 HW: 5G1 920 756
Component: KOMBI 301 4310
Coding: 27AD09083F80000800802A011400000000000000
Shop #: WSC 00046 412 12345
ASAM Dataset: EV_DashBoardVDDMQBAB 009043
ROD: EV_DashBoardVDDMQBAB_009_VW26.rod
VCID: 6ADBC68B8DACC7D9FF-803E

No fault code found.

-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels:| 5Q0-907-530-V1.clb
Part No SW: 5Q0 907 530 AC HW: 5Q0 907 530 F
Component: GW MQB High 128 1204
Revision: -------- Serial number: 0003097448
Coding: 030100342F085900FF00026B9C0F0001000105000000000000 0000000000
Shop #: WSC 00046 412 12345
GVL: 01543C5000000000400C90000000CC00000000000000000000 00000000000000
ASAM Dataset: EV_GatewLear 011020
ROD: EV_GatewLear_011.rod
VCID: 72EBDEEBA57C0F1947-8026

Generator:

Multifunction steering wheel control module:
Subsystem 2 - Part No SW: 5G0 959 442 N HW: 5G0 959 442 N
Labels: 3C8-959-537.CLB
Component: E221__MFL-DC1 H06 0038
Serial number: 29140000427050064121
Coding: 2DFFFF

Battery Monitoring Control Module:
Subsystem 3 - Part No SW: 5Q0 915 181 G HW: 5Q0 915 181 G
Component: J367-BDMHella H04 8050
Serial number: 4199495603

No fault code found.

-------------------------------------------------------------------------------
Address 32: Differential Locks (J492) Labels:* 0CQ-907-554.clb
Part No SW: 0CQ 907 554 E HW: 0CQ 907 554 E
Component: Quersperre H52 8040
Serial number: HA1-00002.12.14
Coding: 0001
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_LockElectHA1VW37X 001001
ROD: EV_LockElectHA1VW37X.rod
VCID: 479D5F3FFE7EDAB1C0-8012

No fault code found.

-------------------------------------------------------------------------------
Address 42: Door Elect, Driver (J386) Labels:| 5QX-959-X93-42.clb
Part No SW: 5Q0 959 593 D HW: 5Q0 959 593 B
Component: TSG FS 020 0028
Serial number: 270115BAP14609
Coding: 003E02208001040000000000
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_DCUDriveSideEWMAXKLO 006003
ROD: EV_DCUDriveSideEWMAXCONT.rod
VCID: 428B4E2BD55CFF9917-8016

Rear Driver Side Door Control Module:
Subsystem 1 - Part No SW: 5Q0 959 812 HW: 5Q0 959 812 Labels:
5QX-959-81X-V1.CLB
Component: FOND_FHSG_DRV 005 0005
Serial number: 00000000000005296446
Coding: 0D0000

No fault code found.

-------------------------------------------------------------------------------
Address 44: Steering Assist (J500) Labels:| 5Q0-909-144.clb
Part No SW: 3Q0 909 144 H HW: 3Q0 909 144 H
Component: EPS_MQB_ZFLS 505 5061
Coding: 8103
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_SteerAssisMQB 012140
ROD: EV_SteerAssisMQB_012_VW37.rod
VCID: 377D2FFF8E9EAA31B0-8062

No fault code found.

-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. (J387) Labels:| 5QX-959-X92-52.clb
Part No SW: 5Q0 959 592 D HW: 5Q0 959 592 B
Component: TSG BFS 020 0028
Serial number: 060215BB515856
Coding: 003E02208E01040000800000
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_DCUPasseSideEWMAXKLO 006003
ROD: EV_DCUPasseSideEWMAXCONT.rod
VCID: 41894127D05AE4810E-8014

Rear Passenger Door Control Module:
Subsystem 1 - Part No SW: 5Q0 959 811 HW: 5Q0 959 811 Labels:
5QX-959-81X-V1.CLB
Component: FOND_FHSG_PSG 005 0005
Serial number: 00000000000005331087
Coding: 150000

No fault code found.

-------------------------------------------------------------------------------
Address 55: Headlight Range (J745) Labels:| 7P6-907-357.clb
Part No SW: 7P6 907 357 D HW: 7P6 907 357 A
Component: AFS-ECU H07 0090
Revision: -------- Serial number: --------------
Coding: 029603000B000200
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_HeadlRegulVWAFSMQB 001120
ROD: EV_HeadlRegulVWAFSMQB.rod
VCID: 408F4423DB50ED8901-8014

Left Headlamp Power Output Stage:
Subsystem 1 - Part No SW: 3D0 941 329 E HW: 3D0 941 329 E
Labels: 3D0-941-329.CLB
Component: LeiMo links H01 0002
Coding: 2E0000

Right Headlamp Power Output Stage:
Subsystem 2 - Part No SW: 3D0 941 329 E HW: 3D0 941 329 E
Labels: 3D0-941-329.CLB
Component: LeiMo rechts H01 0002
Coding: 2E0000

No fault code found.

-------------------------------------------------------------------------------
Address 5F: Information Electr.
Cannot be reached

-------------------------------------------------------------------------------
Address A9: Struct. Borne Sound (J869) Labels: 4H0-907-159.clb
Part No SW: 5G0 907 159 HW: 4H0 907 159 A
Component: SAS-GEN 2 H06 0014
Serial number: 150118201063
ASAM Dataset: EV_SoundActuaGen2AU64X 003010
ROD: EV_SoundActuaGen2AU64X.rod
VCID: 6BD5C38F8256DED184-803E

No fault code found.

End-------------------------(Elapsed Time: 05:21)--------------------------

[guile]

just pasting this here from another website as i have a feeling it may come handy for abs coding...

MK100 ABS Coding | Ross-Tech Forums

Retrofitting Adaptive Cruise Control to Mk7 (oh the fun you shall have!) | VW Vortex - Volkswagen Forum

This is an extract from the link above:

"There's a .pdf floating around out there by "Xagico" that lists a pile of different retrofits and mods that can be done on the Mk7; it has a lot of the coding changes to be made. So that's where I started.

In ABS coding, however, the recommendations on Byte24 ( F4 or F8 ) were not accepted by my car. (I'm guessing this is because Xagico is Spanish(?), and the European cars came with some hardware as standard that were not offered on our cars).
Anyway, using the Somnus's spreadsheet, I was able to calculate that Byte24 on my car should be either 16 or 18; I tried 16 there and it worked. Again, YMMV, so do the math for yourself.

Next, I changed Byte26 to F0 - if you install the new rear wheel ABS sensors first and continue to drive your car without making any other changes, you'll probably have a pile of errors on your display. Change this byte and the errors should disappear literally as you're sitting there.
(Xagico's pdf said to change this to 50, and when I had my just the wheel sensors in my car - without swapping the ABS module - "50" made the errors go away. But once the new module was in the car, while I didn't have any errors, ACC would not work. Helpful user at ross-tech forum suggested to try "F0"....and just like that, everything, ACC worked. Not sure how he arrived at F0, but I'm glad he did.

Lastly in Byte29, Xagico said to change it to 39, but that didn't work for me. A user over at Ross-tech's forums helping me out suggested 22 - and that one worked."

[MIG]

It's good to hear you got it sorted; I like to use the VCDS coding helper for these types of things and cross-check other cars' scan logs with the setup you are trying to match.

Don't worry about any coding of the 5F unit, that's only for the menus to show up on the radio.


With your component protection issue, you need to find someone who has access to ODIS, 5054a or vas6154 and access to geko; I know due to the right to repair stuff, some good VAG specialists have access to this now.


There is a shady market of companies "renting" their accounts out in 15min\20min blocks, not going to recommend that here.

[DV52]

@guile: hmmm........ the coding for the ABS module in your VCDS scan doesn't make sense (it doesn't comply with your words about the changes made).

Here's a more elucidating form of the hex03 long-code string from your SCAN report:

Byte	Hex	Binary
00	01	00000001
01	FA	11111010
02	93	10010011
03	A1	10100001
04	54	01010100
05	27	00100111
06	29	00101001
07	6C	01101100
08	07	00000111
09	7B	01111011
10	06	00000110
11	05	00000101
12	41	01000001
13	C5	11000101
14	69	01101001
15	80	10000000
16	C9	11001001
17	2A	00101010
18	94	10010100
19	E0	11100000
20	60	01100000
21	82	10000010
22	96	10010110
23	F7	11110111
24	00	00000000
25	42	01000010
26	00	00000000
27	B9	10111001
28	C2	11000010
29	09	00001001

As you can see - the coding values that you describe are NOT consistent with the list above. Maybe these are the pre-change coding values? If so, please post up the actual SCAN results post changes (the old long-code isn't of much value if you are describing the coding values that worked!)

Don

[guile]

It's good to hear you got it sorted; I like to use the VCDS coding helper for these types of things and cross-check other cars' scan logs with the setup you are trying to match.

Don't worry about any coding of the 5F unit, that's only for the menus to show up on the radio.


With your component protection issue, you need to find someone who has access to ODIS, 5054a or vas6154 and access to geko; I know due to the right to repair stuff, some good VAG specialists have access to this now.


There is a shady market of companies "renting" their accounts out in 15min\20min blocks, not going to recommend that here.

thanks mate and thanks for the reassurance regarding the 5F unit, i wondered if that would be the case. panic over...

I've also managed to get it booked in with VW for component protection removal, lets hope i walk out of there without having to remortgage the house...