Roller Door

[riche543]

Hi all , would anyone be able to help or know where to get one of these in oz: VOLKSWAGEN TRANSPORTER T5 SLIDING DOOR ROLLER GUIDE RIGHT BOTTOM HOOKE – AXI CAR PARTS
I can find left side ones but not right.

I haven’t called Vw genuine parts yet but bet it would be expensive.
Thanks in advance
Riche [emoji1690]


Sent from my iPhone using Tapatalk

[Lucas_R]

It this it perhaps?
for VW TRANSPORTER T5 Sliding Door Roller Hinge / Bottom Right | eBay

Volkswagen T5 Door Roller Guide Door Holder 7H0843398 | eBay

With VW part numbers, its usually only the very last section of the part number that varies between LHD and RHD parts.

[riche543]

It this it perhaps?
for VW TRANSPORTER T5 Sliding Door Roller Hinge / Bottom Right | eBay

Volkswagen T5 Door Roller Guide Door Holder 7H0843398 | eBay

With VW part numbers, its usually only the very last section of the part number that varies between LHD and RHD parts.

Thanks for reply. The first link to eBay is UK I have already asked weather he has the H version which has the hook to hold door when open. Unfortunately he said he doesn’t have. Second link from picture doesn’t look like it has hook. But does advertise all part numbers??? Was hoping to find one closer to oz though. Thanks again
Cheers
Riche [emoji1690]


Sent from my iPhone using Tapatalk

[ozgti]

This is all that's left of the bottom right roller. Door wouldn't close so I took the thing off. Good thing we're on holiday... [emoji849]

Sent from my SM-G960F using Tapatalk

[riche543]

So this is how I fixed it [emoji12]. $6.95 roller from Bunnings cut down old pin tapped out , locktite new screw on. Seems ok [emoji1696].






Sent from my iPhone using Tapatalk

[ozgti]

Have you got the receipt with the sku? Going to have a go at this. I need my sliding door! Lol

Sent from my SM-G960F using Tapatalk

[riche543]

Have you got the receipt with the sku? Going to have a go at this. I need my sliding door! Lol

Sent from my SM-G960F using Tapatalk

Rolltrak 29mm Replacement Convex Bearing and Threaded Stud Axle Roller - Bunnings Australia

You need too drill out the centre pin on this to take the size bolt/screw you are going to use.
My plan was to just use the nut that came with this but there’s not enough room for it. So that’s why I cut old roller pin down then tapped out for a counter sunk bolt/screw. Hope that makes sense. Good luck. [emoji1690][emoji1690][emoji1690]


Sent from my iPhone using Tapatalk

[ozgti]

How did you get the roller off the new pin?

Sent from my SM-G960F using Tapatalk

[riche543]

How did you get the roller off the new pin?

Sent from my SM-G960F using Tapatalk

Drilled it out , don’t remember what size . Depends on what size bolt/ screw your going to use. Or drill out the hole bolt , then make like a bushing sleeve that fits snug between your screw & the new bearing. If you use a counter sunk bolt you might not need a bushing/sleeve. ???


Sent from my iPhone using Tapatalk

[ozgti]

I meant to get the shank out of the new roller.

Sent from my SM-G960F using Tapatalk

[riche543]

Roller Door

I meant to get the shank out of the new roller.

Sent from my SM-G960F using Tapatalk

Yeah I put it in the vise & drilled it out
You should end up with something that resembles say like a roller blade or skateboard wheel
In my pics you can see I used a flat blade countersunk bolt that holds it straight against the old pin I cut down.

Sent from my iPhone using Tapatalk

[LogicprObe]

That's a good fix.
I noticed mine was playing up yesterday but am yet to inspect it to see what's going on.