VW Tiguan Eyelids

[Tiggy1]

I highly doubt this mod has got anywhere yet but I'd be happily put straight if that wasn't the case. For starters the headlamps would need to be split open which is a task in itself on the latest type of lamps because the adhesive used is heat resistant. You would then to (in my understanding) to cut open the top section housing where that little design is. I noticed 4 distinct compartments as part of the headlamp design each of which could house a single high power LED and the chrome internal surround would act as a reflector. Being only 4 LED's though it wouldn't be very wide so not look as good as other manufacturers. If someone pulls its off though I've be really interested in seeing how the finished article looks!

Hi Naresh,
yeah, presumed that was the case - just hoping (like you) that someone had come up with easier solution
Not that keen (or skilled) to start chopping mine up, so might just get some LEDS to replace park light globes and run those as DRL's
Cheers

[HaywireTig]

Does anyone know if changing the headlamps of the Tig... When using a ballast... Ie: headlamps to factory connector underneath, then there are wires from the HID bulb to ballast, then ballast out to....??

[Naresh]

I think all wires go to a single connector on the headlamp rear and the wiring to the ballast (for xenons) is internal to the headlamp.

On another note I've not had my eyelids painted yet as I'm waiting for the funds to get the bi-xenons and levellers fitted.

The Caractere front grill is here though and I'm still deciding on the colour scheme to go with my front end change. I'm going for a subtle look like your Avatar picture.

[HaywireTig]

I think all wires go to a single connector on the headlamp rear and the wiring to the ballast (for xenons) is internal to the headlamp.

On another note I've not had my eyelids painted yet as I'm waiting for the funds to get the bi-xenons and levellers fitted.

The Caractere front grill is here though and I'm still deciding on the colour scheme to go with my front end change. I'm going for a subtle look like your Avatar picture.

Oooooo interesting to see how your Tig turns out with those bi-xenons, eye lids and that yummy Caractere grill!

Sent from my GT-P1000 using Tapatalk

[Naresh]

Guys, those of you have already fitted your eyelids did you use 3M tape or the glue that came in the packaging? I want to be able to go back to standard if I get bored with the look. I plan on having mine fitted by the end of this month as the Bi-xenon headlamps (fingers crossed!) go on in a couple of weeks.

[HaywireTig]

I haven't got mine on yet too mate. I, too, wanna get my aftermarket headlamps fitted in first before I fit them on. I also don't want to permanently glue them on in case I get bored w the look later in the future. So I might use some good 3M double sided tape. Not sure if there's a better alternative. Hmmm

[Captain Bungers]

Guys, those of you have already fitted your eyelids did you use 3M tape or the glue that came in the packaging? I want to be able to go back to standard if I get bored with the look. I plan on having mine fitted by the end of this month as the Bi-xenon headlamps (fingers crossed!) go on in a couple of weeks.

Don't go with the glue - I did and one of them flew off on the highway - I now have to get it repainted. I will be putting it back on with good double sided tape next time.

[HaywireTig]

Geez... Thanks for the tip Cpt.

[Naresh]

Thanks for the tip Captain, I'm glad I asked now. You were lucky to find it after it flying off!

[Captain Bungers]

Thanks for the tip Captain, I'm glad I asked now. You were lucky to find it after it flying off!

Unfortunately after it had been run over a few times...

[Naresh]

Ouch! I should have mine painted and fitted in a couple of weeks time.