Above Forum Ad

Collapse

Announcement

Collapse
No announcement yet.

JH code k-jet 1.8lt 8v turbo setup

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • JH code k-jet 1.8lt 8v turbo setup

    has anyone doen this in aust, what is needed???

    wabit

  • #2
    My mate has a bolt on manifold and turbo setup to bolt onto an 8v Motor. I believe it uses the Turbo from a Golf TDI. He will sell for $1000.
    sigpic Camden GTI Performance. VW / AUDI Specialists
    All Mechanical Work, Log book Servicing, New and used Parts and Imports
    19-20/6 Badgally Road, Campbelltown, 2560
    02 4627 3072 or 0423 051737 www.camdengti.com

    Comment


    • #3
      Have a read & look through this.
      Ton's of info on turboing CIS injected cars



      Some of my parts are here & more to come for my turbo 8v daily driver in the build.

      Basically
      - Volvo 240T(didn't get them in Aust. but can be found on ebay & vw
      vortex classifieds) will require modified fuel lines as they positioned
      differently on the fuel distributor head
      - Audi 5000T Warm up regulator or Volvo 240T Warm up reg (same as above)
      - Distributor vacuum retard canistor or MSD boost timing master to retard the
      igniton as it comes on boost.
      - Exhaust manifold incl at least a 2.25-2.5" exhaust system,turbo of your
      choice(recommend T3 incl. oil line supply & drain into the sump. Water
      cooled turbo's not really needed but optional, just more pipes/hoses!),
      intercooler(not really needed for apllications up to 6-8psi but I would fit
      one anyway) & piping/misc clamps, gaskets, fitting's etc.

      This setup should see approx 170hp+ on a standard 1.8 8v running 8-10psi

      Tim

      Comment


      • #4
        Some early golf dissys have an advance and a retard on them.
        sigpic Camden GTI Performance. VW / AUDI Specialists
        All Mechanical Work, Log book Servicing, New and used Parts and Imports
        19-20/6 Badgally Road, Campbelltown, 2560
        02 4627 3072 or 0423 051737 www.camdengti.com

        Comment


        • #5
          Hey Wabit i have performed such a conversion on my MK2 1.8 8v GTI, its not easy as far as tuning goes that was my biggest problem. I used a
          *wrx sti vf22roller bearing turbo
          *3" mandrel bent stainless exhaust
          *custom mild steel manifold using 1 1/4" steam pipe bends
          *800mm wide intercooler with 2" stainless plumbing
          *MK1 GTI inlet manifold with a MK2 throttle body
          Originally i recurved the dissy with retard on boost and a hobbs pressure switch to activate a fifth injector under boost, i had difficulty sourcing a larger warm up regulator and the engine leaned out in the top end revs. This setup saw 105kw atw on 10 psi, With standard internals and 10:1 compression. In the search for more power and frustrated i took off all the factory injection and fitted an EMS computer with EVO 5 injectors, with the dissy locked and an ignition module fitted the power jumped to 138 kw atw on 14 psi... I would recommend aftermarket injection
          sigpic
          Mk2 GTI 2 door 1.9l 8v turbo 1st mk2 1st engineered water vw nats 09
          Mk1 twin eng twin turb
          scirocco gti 2.1l 16v turb 6spd
          Audi A4 B5 1.8t

          Comment


          • #6
            just found this on ebay... this guy sounds like he knows wat hes doing!

            Comment


            • #7
              Any good pics of your engines with the turbo setups ?
              sigpic MK2 GTI G60

              Comment


              • #8
                Originally posted by Golf Loon
                Some early golf dissys have an advance and a retard on them.
                All of them did.

                Comment

                Working...
                X