Hi everyone,


I recently bought a 2019 132TSI B8 Passat (wagon, 7sp DSG) and took it for a service last week.


Before the service I swore I heard a strange noise from under the bonnet, so I plugged in a generic scan tool and it threw the P00B7 code which is for...

I'm new to this forum and thought I would post it for ideas experience. It can't really be a mechanical fault it's a bit of a curly one but I don't really know how the logic of the circuit works.
I have a 2006 2.5 TDI BNZ transporter. Engine seems to be running perfectly but every time it reaches...

I'm chasing an issue with high crankcase pressure, it's actually a 2005 Transporter T5 with the AXA engine but I believe it's essentially the same motor as a 2.0L Mk4 Golf and early 2000s Beetle.
It has very high crankcase pressure, enough to pop the dipstick tube out and you can feel it quite...

Hi all,

I've got an '06 GTI with an ESP and Tyre Pressure Warning fault following the replacement of a leaking ABS module. The original module was leaking air into the brake lines (I would lose half the pedal after one brake application post brake bleed) but did not have any faults - ABS,...

Heya, So I`m busy looking to install a Boost Gauge and need to know where I can use a boost tap adapter, as well the gauges here are 2bar what does the Diesel 103KW boost? any takers? and if you have some pics too.

then I am doing gauge pods

oil pressure
oil temp...

I recently changed the clutch and clutch master cylinder in my 2008 VW Caravelle. All was well for about a month then yesterday the clutch pedal lost all pressure while driving. Upon investigation I noticed that the pressure line that feeds the clutch master cylinder was leaking. They are brand new...

I’ve recently bought a Amarok 2012 model, had the oil pressure light come on so took it to the mechanic and they did a service, replaced oil, filter and sensor which fixed the problem for about 2 weeks, but had the light come back on. At first intermittently but now quite often. Took it back to the...

I have a 2011 Volkswagen Passat V6 FSI Highline and recently had the Check Engine Light come on. Aside from the light coming on, it drove perfectly normal.

A day or two after however, it had a rough idle on start up, was sluggish, lost power and then ultimately went into limp mode (it...

Hi, just checking if anyone else has had this issue & / or suggestions.
2010 VRS wagon with 221k on the odo. Engine light scan is showing a lean fuel mixture by both my usual service place & local Skoda dealer. Dealer suggests it might be the low pressure fuel lift pump but we haven't...

Hey all, so as some backstory, I have a MK5 Jetta TDI that put a 2.0T FSI into with a K04 and all the mods you'd expect for that sort of upgrade.

I've adapted everything from the body harness, to the fuel system, and I still just have one issue, the car has immo off, and drives perfectly...

Hey everyone, I have a Golf mk6 2013 1.4l

It’s having issues with the transmission where it goes into limp mode within the first few kms (the car loses all power and needs to be restarted) and then I can restart the car and it drives fine, though sometimes it does it multiple times....

Hey everyone, I have a Golf mk6 2013 1.4l.

I have it booked in to be fixed this week, but am hoping to get advice first.

It’s having issues with the transmission where it goes into limp mode within the first few kms (the car loses all power and needs to be restarted)...

Hi guys
I’m getting a bunch of codes come up for my 2013 mk6 golf. It goes into limp mode after a few kms. Then I have to turn the car off restart and it works again. Can happen many times. I’m told it’s the mechatronics probably. But want to make sure before I replace it.
...

Hi all,
At a loss and keen to hear people’s insights.
Picked up a 2006 jetta fsi turbo with the 2.0 gti engine and 220tkm. It was barely running and blowing lots of smoke etc. Thought it could a project for me and a coilpack etc might be the misfire issue and a quick fix.
So over...

Hi All,

Looking to find out more information in regards to Fuel additives.

1. For controlling water contamination do you use an emulsifying or demulsifying additive? Reason why?

Emulsify = Possible injector issues (high pressure & temp produces steam) / lowers...