QLD MK3 VR6 and CL goodies

[Ben J]

Hey guys,

Have a few mk3 bits for sale. Note: some are pretty dirty in the photos, I will clean them up before selling them, just snapped photos of everything while it was all out. Please excuse the cheeky puppy, he insisted in getting in half of the photos.

Parts can be picked up from Zillmere, Brisbane. I'm also happy to post anywhere in Australia/earth at buyers expense, if you're just after one cheap bit though (say under $10) it's not worth the time packing it up and sending it.

All VR6 bits are from an OBD1 VR6.

VR6 Airbox: Bottom has been cut out ("swiss cheese mod") and top has been smoothed - $35


VR6 Upper Intake manifold, standard, top part has been polished (although a bit oxidised now, I could polish it up again though) and rest has been painted black - $40


VR6 Lower Intake manifold - currently has half the runners ported and smoothed, will finish the rest and paint it up before selling - $50


VR6 Exhaust manifold heat shield -gone

VR6 Expansion tank - $15


VR6 Timing chain covers - $15


VR6 fuse/relay box block thing - $20


VR6 Coil pack - gone

Front flares - have been trimmed for rolled gaurds - $5


Duckbill spoiler - $15


Various trim parts - a couple dollars each


3x brake light clusters, i think 2 are right side and 1 left IIRC. $10 each


Interior light - $10


Indicator and wiper stalks, with cruise control - $10 each


VR6 Wheel nut covers - can only find 14 of them. $1 each


Golf and VR6 rear badges -gone

[Ben J]

second post as too many photos for 1...


IAC - Gone

VR6 Power steering pump - $35


VR6 AC Compressor - Gone

10x Ball seat conversion washers. What these are basically are washers that convert conical bolts/nuts to ball seat, for if you want to use conical seat nuts on ball seat wheels (if you are running a spacer for example). Brand new - $15 for the two sets


8380 Mirror blanks - brand new - $25


Euroimage tuning vr6 motor spacers - brand new, will include hardware. Cost well over $100 to get here, I'll sell for $65


Also have a vr6 fuel rail sitting around with 6x injectors which were professionally cleaned shortly before I took the car off the road - Gone

And that's it for now. If you're interested in anything just shoot me a pm or post here.

Cheers,
Ben.

[davo]

How much for the dog?

[Ben J]

Re: MK3 VR6 and CL goodies

Hes not for sale at the moment, but I can include a few of his hairs with any purchase

Sent from my GT-I9305T using Tapatalk 2

[b0k1]

MK3 VR6 and CL goodies

Can I claim the manifolds please

[Ben J]

Re: MK3 VR6 and CL goodies

certainly, ill finish smoothing the lower one tomorrow. Inbox me

Sent from my GT-I9305T using Tapatalk 2

[ffoff]

MK3 VR6 and CL goodies

Those engine spacers, they work on a 2.0?

Also you wouldn't hold the mirror blanks till early next week for me?

[Ben J]

Re: MK3 VR6 and CL goodies

Not sure if they work for a 2.0 to be honest. The mounts are the same but they seem to make a different set for the 2.0. Not sure what the difference is, I think 1 set has a larger gear box spacer than the other if I recall correctly, can't remember which though.

Might be able to hold the mirror blanks. Have been asked about them in a couple pms from people too, so I'll check tomorrow who got first, only a couple of minutes between you haha

Sent from my GT-I9305T using Tapatalk 2

[Ben J]

Someone got in 1 minute before you about the mirror blanks in pm, so theyre sold pending payment. I'll let you know if it falls through.

Also forgot to mention, all engine bits are from an OBD1 VR6.

[ffoff]

MK3 VR6 and CL goodies

Nooooooooooooooooo

[mkIIIgolf]

Are the rear tail light clusters still available??

[Ben J]

Bummmp

[karjadi15]

Cannot PM you mate.
Is the Mounting spacers for the VR6 hard to install?
INTERESTED

[JT92]

hey man, tried to pm but your inbox is full!! I'll take the expansion tank if it still holds pressure and your willing to ship of course...

[Ben J]

Sorry guys I'll clean it out and send you messages later!

Sent from my GT-I9305T using Tapatalk 2