Above Forum Ad

Collapse

Announcement

Collapse
No announcement yet.

Bora V6 4motion K&N typhoon intake kit

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • NSW Bora V6 4motion K&N typhoon intake kit

    Hi guys,

    Up for sale is a K&N intake kit off my Bora 4motion. Had it on the car for roughly 2500 k's before I took it off to sell the car. Comes with new intake pipe, pod filter, heat shield, and the necessary bolts, nuts, brackets and instructions to mount it in place. The piping has the inlet for the MAF sensor that bolts straight in without any modification.

    This is a very worthwhile mod, I found when installed the throttle response was greatly improved and the car pulled harder with a lot less effort.

    These retail for around $700, so looking for around about $350.

    Pickup from Coffs Harbour or will post anywhere in Australia at buyer's expense.

    PM me with any questions






    Project Hairdresser car DIY build has begun...
    '96 Mirage Track car: BC RM Coilovers, 294mm Galant VR4 Brakes, 5 stud conversion, 16x8 Forged Rays MS01S, UR 23mm sway bar, UR Strut Braces, Evo 5 Recaros, MR Lancer electrics interior conversion, Engine + Exhaust in the works

  • #2
    This would probably work on MK4 R32s and GTIs possibly
    1991 BMW 318is RED E30

    Comment


    • #3
      oh man i might want this... but i also have the VTDA.... but this would bolt straight in..... dammit.

      If anyone wants to snaffle my VTDA, I might take this. confused....

      GL with the sale till i get my head right though, and free bumpage.
      MY02 Bora V6 4Mo|Matte Black plastidip|VTDA|R32 Exhaust|R32 dampers and springs|TT pedals|R32 steering wheel|17" 8L S3 rims|R32 sways|Blue Haldex|EBC reds

      Comment


      • #4
        Cheers guys. Just looked it up, the R32 and Bora use different kits. Not sure on what the differences are. Definitely wont fit the GTI though. Completely different setup.

        Project Hairdresser car DIY build has begun...
        '96 Mirage Track car: BC RM Coilovers, 294mm Galant VR4 Brakes, 5 stud conversion, 16x8 Forged Rays MS01S, UR 23mm sway bar, UR Strut Braces, Evo 5 Recaros, MR Lancer electrics interior conversion, Engine + Exhaust in the works

        Comment


        • #5
          Easily modded.....

          Comment


          • #6
            bump it up

            Project Hairdresser car DIY build has begun...
            '96 Mirage Track car: BC RM Coilovers, 294mm Galant VR4 Brakes, 5 stud conversion, 16x8 Forged Rays MS01S, UR 23mm sway bar, UR Strut Braces, Evo 5 Recaros, MR Lancer electrics interior conversion, Engine + Exhaust in the works

            Comment


            • #7
              Bump!!

              Project Hairdresser car DIY build has begun...
              '96 Mirage Track car: BC RM Coilovers, 294mm Galant VR4 Brakes, 5 stud conversion, 16x8 Forged Rays MS01S, UR 23mm sway bar, UR Strut Braces, Evo 5 Recaros, MR Lancer electrics interior conversion, Engine + Exhaust in the works

              Comment

              Working...
              X